Regular Price: $159.00
Special Price $125.00
3.5″ to 3" Dump pipe, to OEM cat back with 100 cell metallic cat in Stainless Steel
This aftermarket downpipe replaces the factory exhaust pipe, unlocking the full potential of your Audi 8P S3, Audi 8P A3 2.0T & Golf MK6 R engine. The Xforce Downpipe is expertly crafted from high-quality stainless steel to ensure a perfect fit and maximum durability.
The increased exhaust flow from the Xforce Downpipe will allow for improved horsepower and torque, giving you a more exhilarating driving experience. The mandrel-bent design and high-flow catalytic converter provide maximum exhaust flow and minimize back pressure, allowing your engine to breathe freely and reach its full potential.
Upgrade your vehicle with the Xforce Downpipe and experience the ultimate in performance.
Fits the following;
Part No: | ES-VW07-KITB |
---|---|
Vehicle Model: | A3, GOLF R, S3 |
Diameter [in]: | 3 |
Material: | Stainless Steel |
Regular Price: $1,000.00
Special Price $880.00
This valve is designed to fit the FSI and TSI engines of the VAG group (VW, Audi, Seat, Skoda) listed below, including the 2011-2013 2.0l engine using the IHI Turbo.
Note: This will ONLY fit the 1.4 turbo engines up to early 2013, where the turbo is mounted at the front of the engine bay. It will not fit engine codes CMBA & CXSB. We designed the slots in the body to cover a large surface area, allowing for a quick release of air, resulting in a unique sounding dumpvalve.
This upgrade/replacement for your original equipment valve integrates seamlessly with the OEM electronics. Using a wiring harness and solenoid, both tested for each specific application, you can confidentially fit a Forge part knowing that there will be no fault codes, check engine lights, or performance issues with the vehicle!
Another particularly unique feature of this product is the included intake manifold tap used to source a vacuum reference for the operation of the valve. This piece also has two other available provisions from which an intake manifold reference can be taken. These extra manifold references can be used for a boost gauge signal, and even a water/meth injection trigger where applicable.
The OEM valve uses a rubber diaphragm and a plastic housing. Both of these materials, but especially the rubber is prone to failure. The rubber can stiffen and go brittle due to the heat from the engine, resulting in diaphragm splitting and boost leak.
Our valve uses full billet alloy construction with a piston based internal design, meaning the issues with the OEM can never happen with ours! To give you even more peace of mind, we made the internals of our valve serviceable. We recommend doing this every 3 years or 20,000 miles, whichever comes first. However, if you don’t want to service your valve yourself you can order the kit and ship your valve back to us and we will carry out the service free of charge! Simply contact us to arrange the service!
The OEM valve internals can also fail if you have your vehicle mapped as the rubber diaphragm is not always strong enough to cope with the increased boost pressure. We build our valves with a spring matched to the original pressure of the car, but include in the kit a spring strong enough to cope with a stage one remap. If you decide to increase the power even more you can guarantee the reliability of our valve by using this spring tuning kit!
This valve was designed by our highly skilled engineers using CAD software to ensure that it will fit with every listed compatible vehicle with ease!
It is particularly well suited to the B7 and B8 chassis Audi A4 and A5 with the 2.0T engine. The valve mounting location on these vehicles is positioned particularly close to the frame rail of the chassis. Compared to competitors our valve has a much shorter overall installed height.
The OEM part numbers we have replaced with our valve include:
Regular Price: $399.00
Special Price $359.00
Fits 1.4T, 1.8T & 2.0T FSI and TSI engines, including the late 2011-2013 2.0 engine fitted with the IHI turbo, (the 1.4T needs additional fitting kit FMBGFK3)
We recommend servicing your valve every 3 years, or 20,000 miles, whichever comes sooner
Forge Motorsport offer this valve option for the 1.4T, 1.8T & 2.0T FSI and TSI engines, including the late 2011-2013 2.0 engine fitted with the IHI turbo, (the 1.4T needs additional fitting kit (FMBGFK3) found in a wide range of vehicles from VW, Seat, Skoda and Audi.
This valve represents the latest evolution of part number FMFSITVR, The result is a full replacement recirculating valve that integrates seamlessly with the OEM electronics and results in absolutely no fault codes, no check engine lights, and no detriment to the performance of the vehicle in any way. Like our full replacement atmospheric valve option, the FMFSITVR and FMFSITAT is fully engineered to remedy the failure issues experienced with the OEM solenoid valves when their diaphragm may rupture which would effectively result in a boost leak.
Our valve uses full billet alloy construction with a piston based internal design that provides for significantly improved reliability over the OEM valves along with lightning fast response. This valve is particularly well suited to the B7 and B8 chassis Audi A4 and A5 with the 2.0T engine. The valve mounting location on these vehicles is positioned particularly close to the frame rail of the chassis, and the overall installed height of our standard replacement valve and spacer combination is such that it conflicts with the chassis at this location.
The FMFSITVR valve has a much shorter overall installed height, which enables fitment of this recirculating valve option onto the B7 and B8 chassis whereas this was previously not an option. Another particularly unique feature of this product is the included intake manifold tap used to source a vacuum reference for the operation of the valve. This piece also has two other available provisions from which an intake manifold reference can be taken. These extra manifold references can be used for a boost gauge signal, and even a water/meth injection trigger where applicable. If this to be installed to the 1.4 Turbo engine, it will be necessary to additionally purchase our boost sensor adaptor FMBGFK3 - please see below in Related Products.
Note: This will ONLY fit the 1.4 turbo engines up to early 2013, where the turbo is mounted at the front of the engine bay. It will not fit engine codes CMBA & CXSB
In The Box:
1 x FMFSITVR Valve
1 x Wiring Harness
1 x Solenoid, Bracket, and Screws
1 x PCV Adaptor Kit
1 x Blue Spring (Uprated)
10 x Cable Ties
1 x 2000mm Length of 4mm Vac Hose
1 x Instruction Booklet
1 x Forge Keyring and Sticker
If you are unsure if this product is suitable for your application, please contact us.
Regular Price: $399.00
Special Price $339.00
Complete the aggressive aesthetic of your RS3 8V Sportback (Pre-facelift) rear with our rear pods/spats - known for their durability and strength. Our newly developed RS3 Sportback Pre-facelift range shares the same strength, durability and technology as our popular Audi S3 and Golf R line up which is trusted by many enthusiasts. Pre-pressed brass fittings on the rear pods allow for installation of our adjustable rear pods/spats winglets (sold separately) to allow for further customisation to individual taste.
All our lip splitters are made from a thick polyethylene composite, making it the strongest product of its type on the market. Each splitter is model specific in its development and design to ensure perfect fitment. The entire production process is done is our Bayswater factory making us proudly Australian made and owned.
MATERIAL & FINISH
Each splitter is developed to become an integral part of your stock body kit, giving it unrivalled rigidity and strength so it can absorb scrapes and protect your bumper.
Strong, impact-resistant, doesn't corrode or chip, and has excellent abrasion resistance (eg. scraping on driveways!)
As strong and light as carbon fibre is, it cracks on impact or when under load and/or stress. Clearcoat can eventually fade or crack, becoming undesirable.
Please note that although all our precision-made ABS accessories are extremely strong and durable, they do not hold the same shatterproof label as our 10mm thick polyethylene composite splitters. The accessories are manufactured in ABS with the intention that they will be lighter, bolt-on attachments that will improve aesthetics and are easily replaceable if they become damaged from varying road conditions.
Experience Flow-Lock rear diffuser for your RS3 8V Sportback (Pre-facelift), sharing the same durability and technology as our renowned WRX, Golf GTI and R & Focus RS line up which is trusted by car enthusiasts worldwide. The rear valance and diffuser fins will clear the RS3 Sportback dual exhaust tips with ease.
The Flow-Lock interlocking system allows for the final assembly of the diffuser fins without tools or fasteners. A simple push and click and the kit is assembled and ready for installation - this means zero exposed hardware giving you the cleanest look for your RS3 Sportback rear.
No more L-brackets, no additional exposed hardware and no double-sided tape, experience the Flow-Lock difference today!