P3 Gauges offer a Multifunction gauge that gives you the information you need while maintaining a clean OEM look. Starting at a price competitive to single feature old-school needle gauges, they offer unmatched feature to price ratio.
All Multi-Gauges include an on-the-fly configuration menu for setting units (BAR/PSI, Farenheit/Celsius MPH/KPH), Shift light, analog boost sensor calibration and more.
Regular Price: $605.00
Special Price $545.00
The P3 V3 Gauge adds even more user control to what the OBD2 Multi-Gauge already offered. Read DTCs on command, remove pids that you don't care to see, configure units settings of individual measurements, calibrate your vehicle speed, read AFR in Lambda.
No more bulky pillar or column pods... No more squinting to read tiny pixelated screens... While retaining the OEM plus design that blends into your interior, the P3 V3 packs a punch with it's bold, bright display that allows you to pick up info at a glance.
Even though the P3 V3 installs in your air vent, we keep in mind that you need that heat and A/C while designing each gauge.
We've torture-tested our gauges to the extreme. From frozen solid at -94 F to physically melting at hundreds of degrees, our gauges function far beyond the limits of the in-car environment.
Check out the V3 install page for configuration and installation info.
Regular Price: $594.00
Special Price $535.00
Regular Price: $229.00
Special Price $146.70
Fits 1.4T, 1.8T & 2.0T FSI and TSI engines, including the late 2011-2013 2.0 engine fitted with the IHI turbo, (the 1.4T needs additional fitting kit FMBGFK3)
We recommend servicing your valve every 3 years, or 20,000 miles, whichever comes sooner
Forge Motorsport offer this valve option for the 1.4T, 1.8T & 2.0T FSI and TSI engines, including the late 2011-2013 2.0 engine fitted with the IHI turbo, (the 1.4T needs additional fitting kit (FMBGFK3) found in a wide range of vehicles from VW, Seat, Skoda and Audi.
This valve represents the latest evolution of part number FMFSITVR, The result is a full replacement recirculating valve that integrates seamlessly with the OEM electronics and results in absolutely no fault codes, no check engine lights, and no detriment to the performance of the vehicle in any way. Like our full replacement atmospheric valve option, the FMFSITVR and FMFSITAT is fully engineered to remedy the failure issues experienced with the OEM solenoid valves when their diaphragm may rupture which would effectively result in a boost leak.
Our valve uses full billet alloy construction with a piston based internal design that provides for significantly improved reliability over the OEM valves along with lightning fast response. This valve is particularly well suited to the B7 and B8 chassis Audi A4 and A5 with the 2.0T engine. The valve mounting location on these vehicles is positioned particularly close to the frame rail of the chassis, and the overall installed height of our standard replacement valve and spacer combination is such that it conflicts with the chassis at this location.
The FMFSITVR valve has a much shorter overall installed height, which enables fitment of this recirculating valve option onto the B7 and B8 chassis whereas this was previously not an option. Another particularly unique feature of this product is the included intake manifold tap used to source a vacuum reference for the operation of the valve. This piece also has two other available provisions from which an intake manifold reference can be taken. These extra manifold references can be used for a boost gauge signal, and even a water/meth injection trigger where applicable. If this to be installed to the 1.4 Turbo engine, it will be necessary to additionally purchase our boost sensor adaptor FMBGFK3 - please see below in Related Products.
Note: This will ONLY fit the 1.4 turbo engines up to early 2013, where the turbo is mounted at the front of the engine bay. It will not fit engine codes CMBA & CXSB
In The Box:
1 x FMFSITVR Valve
1 x Wiring Harness
1 x Solenoid, Bracket, and Screws
1 x PCV Adaptor Kit
1 x Blue Spring (Uprated)
10 x Cable Ties
1 x 2000mm Length of 4mm Vac Hose
1 x Instruction Booklet
1 x Forge Keyring and Sticker
If you are unsure if this product is suitable for your application, please contact us.
Regular Price: $399.00
Special Price $339.00
Front Lowering: 35mm
Rear Lowering: 35mm
Front Axle Weight: Up to 1100kg
Rear Axle Weight: Up to 1090kg
Sporty looks and performance
Progressive spring characteristics
Less weight by using high tension steel
TUV approved
H&R Sport Sway Bars are crafted from a special 50CRV4 steel alloy, the highest tensile strength available.
The quality of the material and design guarantees smooth transitional sway bar function, decreasing feedback response time and increasing stiffness over stock.
H&R Sport Sway Bars improve lateral stability and cornering grip, while reducing body roll. H&R Sport Sway Bars are designed for drivers who desire improved handling without lowering or affecting ride quality. H&R Sport Sway Bars increase stiffness and reduce body roll while maintaining comfort and increasing cornering control, lateral stability, and grip.
A unique feature of H&R Sport Sway Bars are the smooth, machined-like forged ends that, for specific vehicles, allow for adjustability in stiffness.
Being 100% German made means a commitment to doing it right and giving you the best quality product.
Features:
- Reduces body roll
- Highest tensile strength available
- Works with DCC (adaptive suspension)
- Special urethane/Teflon composite bushes that are maintenance free
Swaybar Size:
- Front 24mm
- Rear 26mm
Adjustable:
- Front x2
- Rear x2
Compatibility:
Regular Price: $630.00
Special Price $549.95