Audi - Forge Motorsports - Flow Designs

Product Description

Fits 1.4T, 1.8T & 2.0T FSI and TSI engines, including the late 2011-2013 2.0 engine fitted with the IHI turbo, (the 1.4T needs additional fitting kit FMBGFK3)

We recommend servicing your valve every 3 years, or 20,000 miles, whichever comes sooner

Forge Motorsport offer this valve option for the 1.4T, 1.8T & 2.0T FSI and TSI engines, including the late 2011-2013 2.0 engine fitted with the IHI turbo, (the 1.4T needs additional fitting kit (FMBGFK3) found in a wide range of vehicles from VW, Seat, Skoda and Audi.

This valve represents the latest evolution of part number FMFSITVR, The result is a full replacement recirculating valve that integrates seamlessly with the OEM electronics and results in absolutely no fault codes, no check engine lights, and no detriment to the performance of the vehicle in any way. Like our full replacement atmospheric valve option, the FMFSITVR and FMFSITAT is fully engineered to remedy the failure issues experienced with the OEM solenoid valves when their diaphragm may rupture which would effectively result in a boost leak.

Our valve uses full billet alloy construction with a piston based internal design that provides for significantly improved reliability over the OEM valves along with lightning fast response. This valve is particularly well suited to the B7 and B8 chassis Audi A4 and A5 with the 2.0T engine. The valve mounting location on these vehicles is positioned particularly close to the frame rail of the chassis, and the overall installed height of our standard replacement valve and spacer combination is such that it conflicts with the chassis at this location.

The FMFSITVR valve has a much shorter overall installed height, which enables fitment of this recirculating valve option onto the B7 and B8 chassis whereas this was previously not an option. Another particularly unique feature of this product is the included intake manifold tap used to source a vacuum reference for the operation of the valve. This piece also has two other available provisions from which an intake manifold reference can be taken. These extra manifold references can be used for a boost gauge signal, and even a water/meth injection trigger where applicable. If this to be installed to the 1.4 Turbo engine, it will be necessary to additionally purchase our boost sensor adaptor FMBGFK3 - please see below in Related Products.

Note: This will ONLY fit the 1.4 turbo engines up to early 2013, where the turbo is mounted at the front of the engine bay. It will not fit engine codes CMBA & CXSB

 

In The Box:
1 x FMFSITVR Valve
1 x Wiring Harness
1 x Solenoid, Bracket, and Screws
1 x PCV Adaptor Kit
1 x Blue Spring (Uprated)
10 x Cable Ties
1 x 2000mm Length of 4mm Vac Hose
1 x Instruction Booklet
1 x Forge Keyring and Sticker

If you are unsure if this product is suitable for your application, please contact us.

DETAILS

Complete the aggressive aesthetic of your RS3 8V Sportback (Pre-facelift) rear with our rear pods/spats - known for their durability and strength. Our newly developed RS3 Sportback Pre-facelift range shares the same strength, durability and technology as our popular Audi S3 and Golf R line up which is trusted by many enthusiasts. Pre-pressed brass fittings on the rear pods allow for installation of our adjustable rear pods/spats winglets (sold separately) to allow for further customisation to individual taste.

All our lip splitters are made from a thick polyethylene composite, making it the strongest product of its type on the market. Each splitter is model specific in its development and design to ensure perfect fitment. The entire production process is done is our Bayswater factory making us proudly Australian made and owned.

KIT INCLUDES

• RS3 8V Sportback (PFL) rear pods/spats V3 (Pair)
• 2 Flow Designs stickers
• Fitting kit with black stainless hardware

MATERIAL & FINISH

• 10mm thick polyethylene composite, bevelled edges
• Hand polished satin black

HOW IS YOUR SPLITTER SO STRONG?

Each splitter is developed to become an integral part of your stock body kit, giving it unrivalled rigidity and strength so it can absorb scrapes and protect your bumper.

WHY DO YOU USE POLYETHYLENE COMPOSITE FOR YOUR PRODUCTS?

Strong, impact-resistant, doesn't corrode or chip, and has excellent abrasion resistance (eg. scraping on driveways!)

WHAT ABOUT CARBON FIBRE?

As strong and light as carbon fibre is, it cracks on impact or when under load and/or stress. Clearcoat can eventually fade or crack, becoming undesirable.

USE OF ABS PLASTIC

Please note that although all our precision-made ABS accessories are extremely strong and durable, they do not hold the same shatterproof label as our 10mm thick polyethylene composite splitters. The accessories are manufactured in ABS with the intention that they will be lighter, bolt-on attachments that will improve aesthetics and are easily replaceable if they become damaged from varying road conditions.

DETAILS Our adjustable rear spat winglets will bolt directly onto our RS3 8V Sportback (Pre-facelift) rear spats/pods thanks to the pre-pressed in threaded brass fittings on our rear spats/pods. Fitting kit is provided to ensure perfect fitment and can be adjusted to your liking. Adjustments can be made anywhere between 5mm-20mm on each side increasing the overall width up to 40mm! The RS3 Sportback (Pre-facelift) body kit range shares the same durability and technology as our renowned Volkswagen Golf R and GTI line up which is trusted by car enthusiasts worldwide. KIT INCLUDES RS3 8V Sportback (Pre-facelift) adjustable rear winglets (pair) 2 Flow Designs stickers Fitting kit MATERIAL 4.5mm thick textured ABS FINISH Scratch resistant textured ABS plastic

DETAILS Finish the exterior aesthetic of your RS3 8V Sportback (Pre-facelift) with our side skirt splitters - renowned for their durability under all driving conditions worldwide! The RS3 8V (Pre-facelift) entire body kit range shares the same technology used in our renowned Golf R and Audi S3 line up which is trusted by car enthusiasts around the world. KIT INCLUDES RS3 8V Sportback (Pre-facelift) side skirt splitters (pair) lip kit V3 2 Flow Designs stickers Fitting kit MATERIAL 10mm thick polyethylene composite, bevelled edges FINISH Hand polished satin black

DETAILS Our adjustable side skirt splitter winglets will bolt directly onto our RS3 8V Sportback (Pre-facelift) side skirt splitters thanks to the pre-pressed in threaded brass fittings on our side skirt splitters. Fitting kit is provided to ensure perfect fitment and can be adjusted to your liking. Adjustments can be made anywhere between 5mm-20mm on each side increasing the overall width up to 40mm! The RS3 Pre-facelift body kit range shares the same durability and technology as our renowned Audi S3 and Golf R line up which is trusted by car enthusiasts worldwide. KIT INCLUDES RS3 8V Sportback (Pre-facelift) adjustable side skirt splitter winglets (pair) 2 Flow Designs stickers Fitting kit MATERIAL 4.5mm thick textured ABS FINISH Scratch resistant textured ABS plastic

DETAILS

Experience Flow-Lock rear diffuser for your RS3 8V Sportback (Pre-facelift), sharing the same durability and technology as our renowned WRX, Golf GTI and R & Focus RS line up which is trusted by car enthusiasts worldwide. The rear valance and diffuser fins will clear the RS3 Sportback dual exhaust tips with ease.

The Flow-Lock interlocking system allows for the final assembly of the diffuser fins without tools or fasteners. A simple push and click and the kit is assembled and ready for installation - this means zero exposed hardware giving you the cleanest look for your RS3 Sportback rear.

No more L-brackets, no additional exposed hardware and no double-sided tape, experience the Flow-Lock difference today!  

---

KIT INCLUDES

• RS3 8V Sportback (Pre-facelift) rear diffuser (rear valance and Flow-Lock diffuser fins)
• 2 Flow Designs stickers
• Fitting kit

MATERIAL

• Valance: 10mm thick polyethylene composite, bevelled edges
• Flow-Lock diffuser fins: 4.5mm thick textured ABS 

FINISH

• Valance: Hand polished satin black
• Flow-Lock diffuser fins: scratch resistant textured ABS plastic
• CNC engraved logo and features

DETAILS

Our adjustable front lip splitters extensions will bolt directly onto our RS3 8V Sedan FL front lip splitters thanks to the pre-pressed in threaded brass fittings on our front lip splitter. Fitting kit is provided to ensure perfect fitment and can be adjusted to your liking. Adjustments can be made anywhere between 5mm-20mm on each side increasing the overall width up to 40mm!

Front Lip Splitter and front winglets sold separately.

KIT INCLUDES:

• RS3 8V Sedan FL Front Lip Splitter Extensions (Pair)
• 2 Flow Designs stickers
• Fitting kit

MATERIAL & FINISH:

• 4.5mm thick ABS plastic
• Scratch resistant textured ABS plastic