The IE MK6 Golf R Cold Air Intake Kit is the perfect intake upgrade for your engine bay. Benefits include added horsepower and torque, perfect MAF scaling, improved throttle response, and increased turbo noise. Peak gains are generally 10 Horsepower and Torque.

ADD POWER, TORQUE, AND SOUND

The massive 5” velocity stack and ram-air designed IE Cold Air Intake Kit delivers the most air and horsepower possible. Quickly add horsepower, torque, and aggressive engine and turbo sound to your VW or Audi 2.0T TSI (Gen1/2) engine. 

LEADING FEATURES

• INCREASED HORSEPOWER & TORQUE
• ENHANCED ENGINE, TURBO, & BLOW-OFF SOUND
• HIGH-FLOW BELLMOUTH
• MASSIVE OVER-SIZED AIR FILTER
• BLACK POWDER COAT FINISH
• EASY INSTALL WITH NO MODIFICATIONS
• USES FACTORY MOUNTING GROMMETS & HARDWARE
• HEAT SHIELDING & DIRECTED AIR FLOW
• REINFORCED SILICONE HOSES
• FITS DSG AND MANUAL TRANSMISSIONS

YOUR BUILD DESERVES THE BEST

Feed your 2.0T TSI GTI, Jetta, GLI, CC, or A3 with a supply of cold air with this direct-fit high-flow cold air intake kit. This intake features a generously-sized inlet pipe that connects to the OE mass air flow (MAF) sensor. The MAF sensor receives high-velocity air fed directly from a 5" bellmouth. Our high-flow bellmouth is neatly housed in a heat shield, which separates the air filter from the hot under-hood air, allowing only cold air to be drawn into the turbo inlet directly from the front of the car.

STOCK-LIKE DIRECT FIT

This air intake kit provides all the necessary piping and couplers to plumb the intake system from the turbo to the MAF and then to the heat shield. The heat shield installs using the OE grommets for easy maintenance and reliable mounting with no rubbing or interference with other factory parts.

HIGH-FLOW VELOCITY STACK

The air intake utilizes a high-flow bellmouth behind the air filter to deliver as much air as possible. This bellmouth design increases the air velocity to the MAF and pulls cold air equally from all directions into the filter. This bellmouth is securely fastened to the heat shield as a clean pass-through providing a solid mount for the air filter and turbo inlet pipe. You have no worry about the intake pipe moving around and causing damage unlike other intake kits on the market, which simply clamp the filter onto the end of the inlet pipe or MAF. Furthermore, the bellmouth opening allows for a filter with a very large surface area that can support any horsepower goal. The same filter and bellmouth design have been tested to support over 500HP!

THERMAL BLOCKING HEAT SHIELD

The IE heat shield is designed to create a thermal barrier blocking all of the radiant heat from the engine bay. Only cold air from the front of the vehicle is drawn into the filter from the opening in the radiator support keeping air intake temperatures as cold as possible. This allows factory placement of the intake to be used without placing the filter lower in the vehicle where it can be subjected to engine harming road debris or fluid.

DO YOU NEED AN SAI KIT?

The MK5/MK6 2.0T TSI engine has two different engine codes. CBFA engine codes are equipped from the factory with a secondary air injection (SAI) pump that connects to the factory intake box. These engines require a small breather filter for this SAI line when installing an aftermarket intake. CCTA engine codes do not have this SAI pump and will not require this filter. Identify your engine code using the photos below, and add an SAI filter kit above if needed when ordering your intake.

EASY INSTALLATION

Installation is quick and easy to install with basic tools. The process should take around an hour for most enthusiasts.

CLICK HERE to view and download the Cold Air Intake install guide

REQUIRES AFTERMARKET INTAKE

Due to the larger size of your new inlet pipe, this must be installed with an aftermarket intake. A new silicone adapter is supplied to be a direct fit with a IE Cold Air Intake, or most 3 inch cold air intakes. 
Does not work with the DV+ Diverter Valve or Diverter Valve spacers.

TURBO INLET PIPE FEATURES

• Greatly improves air-flow to turbocharger
• Constant high-flow inner diameter
• Easy install, no modifications necessary
• Long life cast aluminum alloy
• In-house CNC machined for perfect fitment
• No leak o ring seal to turbocharger 
• Outflows stock inlet by 110CFM

IS YOUR STOCK INLET ROBBING POWER?

The factory installed plastic turbo inlet found installed on your VW or Audi Gen 3 1.8T or 2.0T TSI engine is adequate enough for stock cars with factory hardware and ECU calibrations. However, the necked down design becomes a major flow restriction when ran with power upgrades such as cold air intakes, intercoolers, downpipes, and ECU upgrades. 

UPGRADE YOUR TURBO INLET PIPE

The IE Turbo Inlet Pipe helps you to get the most out of your IS38 or IS20 turbo and power upgrades by removing the factory flow restriction. The cast aluminum design allows for a constant diameter elbow increasing efficiency from the intake to the turbo without the bottleneck design of the factory unit.

HORSEPOWER RESULTS

Dyno graph tested on a 2019 GTI with Stage 2 hardware & software on 93 octane

EASY INSTALLATION

Your new turbo inlet pipe has been in-house CNC machined and includes all required hardware to allow for a perfect and easy installation. View and download the install guide here (coming soon).

REQUIRES AFTERMARKET INTAKE

Due to the larger size of your new inlet pipe, this must be installed with an aftermarket intake. A new silicone adapter is supplied to be a direct fit with a IE Cold Air Intake, or most 3 inch cold air intakes. 
Does not work with the DV+ Diverter Valve or Diverter Valve spacers. 

VEHICLE APPLICATIONS

• Audi - A3 2015+ 8V 1.8T & 2.0T engines
• Audi - S3 2015+ 8V 2.0T engine
• Audi - TT 2016+ 8S 2.0T engine
• Audi - TTS 2016+ 8S 2.0T engine
• VW - Golf R 2015+ MK7 2.0T engine
• VW - GTI 2015+ MK7 2.0T engine
• VW - Golf/Alltrak 2015+ MK7 1.8T & 2.0T
• VW - Passat 2013+ B8 1.8T & 2.0T (EA888 Gen 3) engines
• VW - Tiguan 5N 2017+ 2.0T (EA888 Gen 3) engine

This is a CTS Turbo universal 3.5″ cone filter, it has a tapered design primarily used in our MK7 GTI/GOLF R, B9 AUDI A4, B8/B8.5 S4, S5  intake kits.  These filters can also be used in a custom big turbo application.

Product Details:

3.5″ Inlet x 8.0″ Long x 6.0″ Wide
High quality moulded silicon base and cap
Stainless steel clamp

Fitment:

• CTS-IT-270R or CTS-IT-270
• CTS-IT-290
• CTS-IT-300

Description

MK7 Golf/GTI/Golf R (up to production date Sept 27, 2015) 8V Audi A3/S3 (up to production date Sept 27, 2015) MK3 Audi TT/TT-S (up to production date Sept 27, 2015)

T304 Seamless Stainless Steel tubing -T304 Stainless Steel flanges -100% TIG Welded -T304 Stainless Steel 02 bung -Torca Accuseal Stainless Steel Clamps -Great Sound even with factory exhaust, no drone!! To ensure the best performance and operation, proper tuning software must be used (Stage 2 software from most large tuning companies is compatible).

Mandrel bent aluminum piping with durable black powder coating - CNC machined MAP flange - 4 Ply silicon connectors with stainless steel clamps - Integrated water methanol bung with plug - Stainless steel clamps

Audi - S1 EA888 Gen 3 - 2.0 TFSI Audi - A3 & S3 (MK3) - EA888 Gen 3 - 1.8 TFSI and 2.0 TFSI Audi - A4 / Allroad (B8 & B8.5) - EA888 Gen 2 & 3 - 2.0 TFSI Audi - A5 (B8 & B8.5) - EA888 Gen 2 & 3 - 2.0 TFSI Audi - A6 (C6 & C7) - EA888 Gen 2 - 2.0 TFSI Audi - Q5 - EA888 Gen 2 & 3 - 2.0 TFSI Audi - TT / TTS (MK3) - EA888 Gen 3 - and 2.0 TFSI VW - Golf / GTI / R (MK7) - EA888 Gen 3 - 1.8 TSI and 2.0 TSI