Volkswagen - H&R Springs - Leyo Motorsport - Integrated Engineering - Whiteline
H&R Lowering Springs - MK5 R32
H&R Lowering Springs - VW Polo GTI
H&R Lowering Springs - VW MK5 Golf GTI
H&R Lowering Springs - VW Polo GTI
H&R Lowering Springs - VW UP 11/11 and VW UP Facelift eUP (2016+)
Drop Front: 35mm
Drop Rear: 35mm
H&R Lowering Springs - Golf MK8 GTI
Lowering Levels:
Front 40mm
Rear 40mm
Enhance the look of your vehicle with H&R Lowering Springs. H&R Sport Springs provide a lower center of gravity and reduce body roll for better handling. The progressive spring rate design provides superb ride quality and comfort. A lower wind resistance signature will make the vehicle more streamlined and improve gas mileage. If you are only looking to improve one part of your vehicle's suspension, you cannot go wrong with installing sport springs. Fun to drive, H&R Sport Springs are the number one upgrade for your vehicle.
Sporty look and performance
Progressive spring characteristics
Less weight by using high tension steel
TUV approved
Description
The IE MQB HPFP upgrade kit unlocks fuel delivery for ethanol, larger turbos, and our TrueFlex ECU tunes for the VW & Audi MK7 & 8V 2.0T Gen 3 engines. The piston and cylinder assembly is the largest volume possible within the stock fuel pump body. Top-quality components and our strict QC process ensure extreme reliability. Increase your fueling overhead and enjoy worry-free HPFP operation for your MQB 2.0L turbocharged engine.
- Highest flowing MQB HPFP upgrade on the market
- HPFP upgrade for ethanol & larger turbo tunes
- Fueling support for IE TrueFlex & ethanol tunes
- Reliably adds a larger fuel ceiling for increased flow
- The piston diameter increased from 9.92mm to 11.68mm
- Stroke volume increased from 231mm^3 to 321mm^3
- Broken-in and bench tested on in-house pump dyno
- Constant diameter piston design for long-life operation
- Tool steel DLC coated pin
- Nitrided tool steel cylinder
- Molybdenum disulphide impregnated leak-free seal
- Stainless steel seal body
- Buna-N rubber oil resistant o ring
- Engineered, designed, & manufactured in the USA
Your HPFP is an integral part of the MQB platform direct injection (DI) system and provides exceptionally high-pressure fuel (exceeding 2900psi) to the injectors. When running turbo upgrades or ethanol fuel, the stock HPFP internal volume becomes the limiting factor when increasing power. IE’s HPFP internals install into your factory pump housing and increase the bore and piston size of the pump internals, allowing more flow, delivering more fuel, and allowing for more horsepower & torque.
Upgrading to IE’s HPFP reliably increases the flow rate of the high-pressure pump for more tuning headroom to increase power safely. The result is a maximum gain of 38.58% over stock!
Every piston and cylinder is CNC machined to exacting sizes, assembled, and measured as a matching set in-house. Tolerances are hand-verified using specialized measurement tools and verified down to 0.00005 of an inch to ensure reliability and proper function. These extreme manufacturing and QC processes are the foundation that has built IE’s leading reputation in HPFP reliability and the popular choice for anyone wanting worry-free operation.
Engineered & manufactured in the USA
IE HPFP designs are verified and torture-tested on our own application-specific fuel pump dyno. This machine is able to replicate countless miles and various RPM situations to substantiate every detail of the HPFP design. This strict engineering process, combined with our 100% in-house CNC machining, obsessed quality control, and top-shelf components is why IE HPFP Kits have earned their esteem and reputation for reliability.
INCLUDED LIMITED WARRANTY
Due to the extreme machining and coating tolerances, Integrated Engineering offers a limited warranty on this product:
Six months from the day of purchase (unlimited miles) for MQB internal HPFP kits.
DLC (diamond-like carbon coating) is an advanced coating process applied to the tool steel pin. This coating combines hardness and low friction, providing excellent wear properties and self-lubrication behavior that drastically extends pin life.
Many aftermarket HPFP options use a stepped-diameter piston in a cost-saving effort to reuse the factory seal. This design dramatically reduces the contact between the pin and cylinder, causing instability of the pin stroke leading to increased wear. IE’s uniquely designed constant diameter pinmaintains its larger size through the entire piston shaft. This engineering detail increases the contact between the pin and cylinder by over 50% compared to kits which do not replace the seal and nut, increasing pin stability.
The cylinder can see up to 19000 strokes a minute with an astonishingly thin tolerance and is lubricated by fuel only. Our tool steel cylinder is nitrided to guarantee it can withstand this torture. This advanced process infuses nitrogen atoms into the atomic structure of the outer surface of the component, increasing surface hardness and wear properties drastically. The thickness and quality of every nitride production batch are independently verified in a specialty lab.
Our ultra-lightweight FEA optimized titanium retainer reduces the chance of valve float while securing the spring to the new IE pump assembly. The internal kit is designed correctly for the factory spring rate, avoiding the need for a stiffer spring that adds unnecessary pressure and wear on the camshaft.
A custom CNC Machined nut holds our molybdenum disulphide impregnated PTFE seal, which is ideal for reducing friction and maintaining stiffness. The seal is spring energized to increase reliability and provide constant outward pressure. The body is sealed to the pump with a quality Buna-N rubber o ring, ensuring it will hold up against heat and a wide range of fuels. What may seem like minor features add up to ensure long life and trouble-free operation.
Update the look of your ugly stock plastic valve cover to a show-ready one piece machined billet aluminum IE valve cover on your 2.0T FSI (EA113) engine!
PRODUCT DETAILS
IE billet aluminum valve covers for the 2.0T FSI EA113 (timing belt driven) engines are a direct replacement for your factory valve cover for a clean updated look over the stock plastic valve cover. Designed as a perfect solution for a show-ready look or the base for your custom catch can project.
MACHINED DESIGN
Machined in-house from a solid block of aircraft grade aluminum for an attractive one piece design with a matching oil filler cap to finish off the look. The IE billet valve cover is machined to accept the factory valve cover gasket, so there is no worry of oil leaks.
FOR USE WITH CUSTOM CATCH CAN SETUPS ONLY
This valve cover design completely removes the factory PCV breather setup and will require a custom catch can kit or breather setup. IE complete catch can kits for the billet valve cover are available separately for select models (located in required hardware tab). To make setting up a custom breather or catch can kit easy, this valve cover features a single -10an breather outlet providing a simple start for a variety of fittings or hose ends. The breather outlet is located above an integrated baffle system to reduce oil escaping the breather outlet. These baffles are hand welded into the valve cover, ensuring they will not fail or fall into the cylinder head.
PRODUCT FEATURES
- Replaces factory plastic valve cover
- Uses factory valve cover gasket
- In-house CNC machined from aluminum
- Includes o ring sealed matching billet oil cap
- -10AN breather outlet for catch can setups
ADDITIONAL PARTS REQUIRED
EVAP CROSSOVER TUBE RELOCATION KIT
The factory plastic valve cover has an integrated evap line crossing through the center of the valve cover. The IE billet valve cover does not have this vacuum line running through the center, and requires The IE Evap Crossover Tube Relocation Kit. This kit includes everything needed to re-run the EVAP line hiding it away for a stealthy look. IE Part Number: IEBAVC11
CATCH CAN KIT FOR BILLET VALVE COVER
The IE billet valve cover replaces the factory breather setup for a single -10AN breather outlet requiring you to run a custom catch can kit setup. IE has taken the leg work out of piecing together a catch can kit for transverse mounted 2.0T FSI engines commonly found in VW MK6 Golf R, MK5 GTI, Jetta, GLI and Audi MK2 TT, TTS, and A3 among others. This catch can kit includes everything you need to completely install the IE billet valve cover breather system. IE Part Number: IEBACC3
VEHICLE FITMENT
- Audi - A4 2005-2008 (B7) 2.0T FSI (EA113) engines
- Audi - A6 2005-2011 (C6) 2.0T FSI (EA113) engines
- Audi - A6 Allroad 2005-2011 (C6) 2.0T FSI (EA113) engines
- Audi - TT 2008-2015 (MK2 - 8J) 2.0T FSI (EA113) engines*
- Audi - TTS 2008-2015 (MK2 - 8J) 2.0T FSI (EA113) engines
- Audi - A3 2006-2013 (MK2 - 8P) 2.0T FSI (EA113) engines*
- Audi - S3 2006-2013 (MK2 - 8P) 2.0T FSI (EA113) engines
- VW - GTI 2006-2009 (MK5) 2.0T FSI (EA113) engines*
- VW - Golf R 2012-2012 (MK6) 2.0T FSI (EA113) engines
- VW - Jetta & Jetta GLI 2006-2010 (MK5) 2.0T FSI (EA113) engines*
- VW - Passat 2006-2010 (B6) 2.0T FSI (EA113) engines*
- VW - EOS 2006-2015 (1F7) 2.0T FSI (EA113) engines*
*This billet valve cover will only work on early model 2.0T EA113 engines. You can verify your the correct engine if it is in the above chassis and is driven by a timing belt. If your engine is driven by a timing chain, you have an EA888 Gen1/Gen2 TSI engine and is not compatible with billet valve covers.
H&R Sport Sway Bars are crafted from a special 50CRV4 steel alloy, the highest tensile strength available.
The quality of the material and design guarantees smooth transitional sway bar function, decreasing feedback response time and increasing stiffness over stock.
H&R Sport Sway Bars improve lateral stability and cornering grip, while reducing body roll. H&R Sport Sway Bars are designed for drivers who desire improved handling without lowering or affecting ride quality. H&R Sport Sway Bars increase stiffness and reduce body roll while maintaining comfort and increasing cornering control, lateral stability, and grip.
A unique feature of H&R Sport Sway Bars are the smooth, machined-like forged ends that, for specific vehicles, allow for adjustability in stiffness.
Being 100% German made means a commitment to doing it right and giving you the best quality product.
Features:
- Reduces body roll
- Highest tensile strength available
- Works with DCC (adaptive suspension)
- Special urethane/Teflon composite bushes that are maintenance free
Swaybar Size:
- Front 24mm
- Rear 26mm
Adjustable:
- Front x2
- Rear x2
Compatibility:
- Audi A3 8P 2003-2012 4WD
- Audi S3 8P 2003-2012 4WD
- Skoda SUPERB 3T SEDAN 4WD
- Skoda OCTAVIA 1Z SEDAN + WAGON 4WD
- VW GOLF MK5 2003-2008 4WD
- VW GOLF MK6 2008-2012 4WD
- VW PASSAT B6/B7 2005-2014 4WD
- VW Tiguan 5N 2007-2015 4WD
EVAP Crossover Tube Relocation Kit for 2.0T FSI with IE Valve Cover
