Volkswagen - Forge Motorsports - Integrated Engineering

REQUIRES AFTERMARKET INTAKE

Due to the larger size of your new inlet pipe, this must be installed with an aftermarket intake. A new silicone adapter is supplied to be a direct fit with a IE Cold Air Intake, or most 3 inch cold air intakes. 
Does not work with the DV+ Diverter Valve or Diverter Valve spacers.

TURBO INLET PIPE FEATURES

• Greatly improves air-flow to turbocharger
• Constant high-flow inner diameter
• Easy install, no modifications necessary
• Long life cast aluminum alloy
• In-house CNC machined for perfect fitment
• No leak o ring seal to turbocharger 
• Outflows stock inlet by 110CFM

IS YOUR STOCK INLET ROBBING POWER?

The factory installed plastic turbo inlet found installed on your VW or Audi Gen 3 1.8T or 2.0T TSI engine is adequate enough for stock cars with factory hardware and ECU calibrations. However, the necked down design becomes a major flow restriction when ran with power upgrades such as cold air intakes, intercoolers, downpipes, and ECU upgrades. 

UPGRADE YOUR TURBO INLET PIPE

The IE Turbo Inlet Pipe helps you to get the most out of your IS38 or IS20 turbo and power upgrades by removing the factory flow restriction. The cast aluminum design allows for a constant diameter elbow increasing efficiency from the intake to the turbo without the bottleneck design of the factory unit.

HORSEPOWER RESULTS

Dyno graph tested on a 2019 GTI with Stage 2 hardware & software on 93 octane

EASY INSTALLATION

Your new turbo inlet pipe has been in-house CNC machined and includes all required hardware to allow for a perfect and easy installation. View and download the install guide here (coming soon).

REQUIRES AFTERMARKET INTAKE

Due to the larger size of your new inlet pipe, this must be installed with an aftermarket intake. A new silicone adapter is supplied to be a direct fit with a IE Cold Air Intake, or most 3 inch cold air intakes. 
Does not work with the DV+ Diverter Valve or Diverter Valve spacers. 

VEHICLE APPLICATIONS

• Audi - A3 2015+ 8V 1.8T & 2.0T engines
• Audi - S3 2015+ 8V 2.0T engine
• Audi - TT 2016+ 8S 2.0T engine
• Audi - TTS 2016+ 8S 2.0T engine
• VW - Golf R 2015+ MK7 2.0T engine
• VW - GTI 2015+ MK7 2.0T engine
• VW - Golf/Alltrak 2015+ MK7 1.8T & 2.0T
• VW - Passat 2013+ B8 1.8T & 2.0T (EA888 Gen 3) engines
• VW - Tiguan 5N 2017+ 2.0T (EA888 Gen 3) engine

Product Description

• Direct OEM replacement
• Made from the highest quality Aircraft quality T6061 billet aluminium construction
• Fully compatible with OEM electronics
• Fully serviceable piston
• Capable to 600HP (with uprated spring kit)
• Utilising world leading springs for more precise operation and consistency
• All internal and external components have been made in the UK
• Pistons use heat stabilised Viton O-rings
• Lubricated with high temperature Mobil1 grease
• Fully serviceable and rebuildable in minutes
• Unlike other valves on the market, ours produce no check engine lights (EML)
• Improved dynamic throttle response
• Consistent turbo boost & reduced turbo lag
• Covered by the Forge Lifetime Warranty*

This valve is designed to fit the FSI and TSI engines of the VAG group (VW, Audi, Seat, Skoda) listed below, including the 2011-2013 2.0l engine using the IHI Turbo.

• 1.4T (with additional fitting kit FMBGFK3)
• 1.8T
• 2.0T

Note: This will ONLY fit the 1.4 turbo engines up to early 2013, where the turbo is mounted at the front of the engine bay. It will not fit engine codes CMBA & CXSB. We designed the slots in the body to cover a large surface area, allowing for a quick release of air, resulting in a unique sounding dumpvalve.

 

This upgrade/replacement for your original equipment valve integrates seamlessly with the OEM electronics. Using a wiring harness and solenoid, both tested for each specific application, you can confidentially fit a Forge part knowing that there will be no fault codes, check engine lights, or performance issues with the vehicle!

Another particularly unique feature of this product is the included intake manifold tap used to source a vacuum reference for the operation of the valve. This piece also has two other available provisions from which an intake manifold reference can be taken. These extra manifold references can be used for a boost gauge signal, and even a water/meth injection trigger where applicable.

The OEM valve uses a rubber diaphragm and a plastic housing. Both of these materials, but especially the rubber is prone to failure. The rubber can stiffen and go brittle due to the heat from the engine, resulting in diaphragm splitting and boost leak.

Our valve uses full billet alloy construction with a piston based internal design, meaning the issues with the OEM can never happen with ours! To give you even more peace of mind, we made the internals of our valve serviceable. We recommend doing this every 3 years or 20,000 miles, whichever comes first. However, if you don’t want to service your valve yourself you can order the kit and ship your valve back to us and we will carry out the service free of charge! Simply contact us to arrange the service!

The OEM valve internals can also fail if you have your vehicle mapped as the rubber diaphragm is not always strong enough to cope with the increased boost pressure. We build our valves with a spring matched to the original pressure of the car, but include in the kit a spring strong enough to cope with a stage one remap. If you decide to increase the power even more you can guarantee the reliability of our valve by using this spring tuning kit!

This valve was designed by our highly skilled engineers using CAD software to ensure that it will fit with every listed compatible vehicle with ease! 

It is particularly well suited to the B7 and B8 chassis Audi A4 and A5 with the 2.0T engine. The valve mounting location on these vehicles is positioned particularly close to the frame rail of the chassis. Compared to competitors our valve has a much shorter overall installed height.

The OEM part numbers we have replaced with our valve include:

• 06H145710B
• 06H145710C
• 06H145710D
• 06H145710F
• 06H145710G

Product Description

Fits 1.4T, 1.8T & 2.0T FSI and TSI engines, including the late 2011-2013 2.0 engine fitted with the IHI turbo, (the 1.4T needs additional fitting kit FMBGFK3)

We recommend servicing your valve every 3 years, or 20,000 miles, whichever comes sooner

Forge Motorsport offer this valve option for the 1.4T, 1.8T & 2.0T FSI and TSI engines, including the late 2011-2013 2.0 engine fitted with the IHI turbo, (the 1.4T needs additional fitting kit (FMBGFK3) found in a wide range of vehicles from VW, Seat, Skoda and Audi.

This valve represents the latest evolution of part number FMFSITVR, The result is a full replacement recirculating valve that integrates seamlessly with the OEM electronics and results in absolutely no fault codes, no check engine lights, and no detriment to the performance of the vehicle in any way. Like our full replacement atmospheric valve option, the FMFSITVR and FMFSITAT is fully engineered to remedy the failure issues experienced with the OEM solenoid valves when their diaphragm may rupture which would effectively result in a boost leak.

Our valve uses full billet alloy construction with a piston based internal design that provides for significantly improved reliability over the OEM valves along with lightning fast response. This valve is particularly well suited to the B7 and B8 chassis Audi A4 and A5 with the 2.0T engine. The valve mounting location on these vehicles is positioned particularly close to the frame rail of the chassis, and the overall installed height of our standard replacement valve and spacer combination is such that it conflicts with the chassis at this location.

The FMFSITVR valve has a much shorter overall installed height, which enables fitment of this recirculating valve option onto the B7 and B8 chassis whereas this was previously not an option. Another particularly unique feature of this product is the included intake manifold tap used to source a vacuum reference for the operation of the valve. This piece also has two other available provisions from which an intake manifold reference can be taken. These extra manifold references can be used for a boost gauge signal, and even a water/meth injection trigger where applicable. If this to be installed to the 1.4 Turbo engine, it will be necessary to additionally purchase our boost sensor adaptor FMBGFK3 - please see below in Related Products.

Note: This will ONLY fit the 1.4 turbo engines up to early 2013, where the turbo is mounted at the front of the engine bay. It will not fit engine codes CMBA & CXSB

 

In The Box:
1 x FMFSITVR Valve
1 x Wiring Harness
1 x Solenoid, Bracket, and Screws
1 x PCV Adaptor Kit
1 x Blue Spring (Uprated)
10 x Cable Ties
1 x 2000mm Length of 4mm Vac Hose
1 x Instruction Booklet
1 x Forge Keyring and Sticker

If you are unsure if this product is suitable for your application, please contact us.

The Integrated Engineering MK5/MK6 FDS intercooler system was built from the ground up to offer the ultimate in performance for your vehicle. When increasing the power output of your engine it is extremely important to ensure it has the proper cooling to match. It packs a very large intercooler core into the space available, a full 54% larger than the OEM core. This large core delivers cool air to the engine under all circumstances, increasing power and torque and simultaneously reducing heat soak.  

One of the most common failures on the 2.0T FSI engine is the factory pressure-relief valve. These valves are in place to recirculate crankcase gases into the intake manifold once they open. Although this works fine for a few thousand miles, they begin to leak over time and cause boost to go past the valve into the valve cover. This not only causes an oily mess in the engine bay from crankcase pressure, but a rough idle, fuel economy decline and boost loss. With boost pressure far below where it should be, it is common to notice significant power losses and poor drivability.

EVAP Crossover Tube Relocation Kit for 2.0T FSI with IE Valve Cover

This recirculating catch can kit has been designed for use with the IE billet valve cover (IE part number: IEBAVC5) as a simple install solution for your billet valve cover and catch can. 
IE billet valve cover sold separately. 

 

Product Features

 

Update the look of your ugly stock plastic valve cover to a show-ready one piece machined billet aluminum IE valve cover on your 2.0T FSI (EA113) engine!

PRODUCT DETAILS

IE billet aluminum valve covers for the 2.0T FSI EA113 (timing belt driven) engines are a direct replacement for your factory valve cover for a clean updated look over the stock plastic valve cover. Designed as a perfect solution for a show-ready look or the base for your custom catch can project.

MACHINED DESIGN

Machined in-house from a solid block of aircraft grade aluminum for an attractive one piece design with a matching oil filler cap to finish off the look. The IE billet valve cover is machined to accept the factory valve cover gasket, so there is no worry of oil leaks.

FOR USE WITH CUSTOM CATCH CAN SETUPS ONLY

This valve cover design completely removes the factory PCV breather setup and will require a custom catch can kit or breather setup. IE complete catch can kits for the billet valve cover are available separately for select models (located in required hardware tab). To make setting up a custom breather or catch can kit easy, this valve cover features a single -10an breather outlet providing a simple start for a variety of fittings or hose ends. The breather outlet is located above an integrated baffle system to reduce oil escaping the breather outlet. These baffles are hand welded into the valve cover, ensuring they will not fail or fall into the cylinder head.

PRODUCT FEATURES

 

• Replaces factory plastic valve cover
• Uses factory valve cover gasket
• In-house CNC machined from aluminum
• Includes o ring sealed matching billet oil cap
• -10AN breather outlet for catch can setups

ADDITIONAL PARTS REQUIRED

 

EVAP CROSSOVER TUBE RELOCATION KIT

The factory plastic valve cover has an integrated evap line crossing through the center of the valve cover. The IE billet valve cover does not have this vacuum line running through the center, and requires The IE Evap Crossover Tube Relocation Kit. This kit includes everything needed to re-run the EVAP line hiding it away for a stealthy look. IE Part Number: IEBAVC11

CATCH CAN KIT FOR BILLET VALVE COVER

The IE billet valve cover replaces the factory breather setup for a single -10AN breather outlet requiring you to run a custom catch can kit setup. IE has taken the leg work out of piecing together a catch can kit for transverse mounted 2.0T FSI engines commonly found in VW MK6 Golf R, MK5 GTI, Jetta, GLI and Audi MK2 TT, TTS, and A3 among others. This catch can kit includes everything you need to completely install the IE billet valve cover breather system. IE Part Number: IEBACC3

 

VEHICLE FITMENT

• Audi - A4 2005-2008 (B7) 2.0T FSI (EA113) engines
• Audi - A6 2005-2011 (C6) 2.0T FSI (EA113) engines
• Audi - A6 Allroad 2005-2011 (C6) 2.0T FSI (EA113) engines
• Audi - TT 2008-2015 (MK2 - 8J) 2.0T FSI (EA113) engines*
• Audi - TTS 2008-2015 (MK2 - 8J) 2.0T FSI (EA113) engines
• Audi - A3 2006-2013 (MK2 - 8P) 2.0T FSI (EA113) engines*
• Audi - S3 2006-2013 (MK2 - 8P) 2.0T FSI (EA113) engines
• VW - GTI 2006-2009 (MK5) 2.0T FSI (EA113) engines*
• VW - Golf R 2012-2012 (MK6) 2.0T FSI (EA113) engines
• VW - Jetta & Jetta GLI 2006-2010 (MK5) 2.0T FSI (EA113) engines*
• VW - Passat 2006-2010 (B6) 2.0T FSI (EA113) engines*
• VW - EOS 2006-2015 (1F7) 2.0T FSI (EA113) engines*

*This billet valve cover will only work on early model 2.0T EA113 engines. You can verify your the correct engine if it is in the above chassis and is driven by a timing belt. If your engine is driven by a timing chain, you have an EA888 Gen1/Gen2 TSI engine and is not compatible with billet valve covers.

SHIFT FASTER, DRIVE FASTER The IE DSG Tune for your VW MK6 GTI, Jetta, GLI, or Audi 8J TTS 2.0T delivers increased power, higher RPM limit, faster shifts, optimized shift points, adjustable launch control, and additional transmission performance features when paired with a matching ECU tune. Acceleration times will greatly improve turning your tuned 2.0T TSI into a fully rounded performance monster. LEADING FEATURES Lightning fast gear shifts Higher shift points of 6800 RPM Kick down in manual mode eliminated Lag time reduced when starting off in first gear Multiple launch RPMs: 3200, 3400, 3600, 3800, 4000 Drive shift mapping entirely reworked with an enthusiast in mind Flashed directly through OBD-II Port (No TCU removal required) Works flawlessly with an IE ECU tune Increased clutch pressure on tap for higher torque without slip Temperature protection remains for safety Gear hunting reduced Gearbox “Torque Limiters” removed WHAT DOES A DSG TRANSMISSION TUNE DO? The IE DSG Tune for the MK6 2.0T TSI has been carefully set up to make the car way more fun to drive. It completely reworks the shift point mapping in both drive and sport. The transmission will no longer lug the engine in drive mode. Clutch clamping forces are increased so the transmission can safely handle much more power. Shifts are much, much faster taking time directly off the 0-60 and ¼ mile times. ONE TUNE FOR ALL STAGES IE’s TCU/DSG tune is all-inclusive and does not offer expensive upgrades. That’s right, there are no unnecessary upgrade charges and all features are included from the outset. A great deal of sportiness is added from the tune while maintaining factory smoothness and driveability. More aggressive launches and faster shifts are guaranteed to put a smile on your face. Also, expect acceleration and 0-60 times to improve from faster shifting. DSG tune requires a matching ECU Tune, do not install on stock ECU tunes. USER ADJUSTABLE LAUNCH CONTROL The purchase of an IE DSG file grants you access to customization of launch points. With several launch points to choose from you can pick what works best for your setup! Available Launch Control RPMs: 3200 RPM 3400 RPM 3600 RPM 3800 RPM 4000 RPM IE DSG TUNE TECHNICAL FEATURES HIGHER SHIFT POINTS Utilize the whole powerband of your 2.0 TSI engine without the DSG interfering and shifting early. DRIVE MAPPING REWORKED The MK6 2.0 TSI DSG is designed to a fault to keep engine rpm extremely low in drive. We completely reworked this, creating a more enthusiast-friendly drive mapping which shifts a bit higher. This eliminates vibration and that constant feeling that you’re lugging the engine. We’ve reworked the downshifting aspect as well, making the transmission much quicker to deliver power when you need it. Thousands of miles of testing were accumulated and a variety of users were polled to come up with this improved drive mode. INCREASED CLUTCH PRESSURE Increasing the clutch pressure allows for the transmission to hold more torque without causing clutch damage or expedited wear. With the increased torque, the acceleration will be greatly increased and launches will far more aggressive. FLASHED THROUGH OBD-II PORT There’s no need to remove the TCU from the car and it can be flashed in your driveway or through an IE software dealer. Additionally, having an IE PowerLink cables means you can install updates are they become available as well as read TCU and ECU fault codes. TAKE-OFF LAG REDUCED The clutch engagement has been reworked to reduce that annoying “DSG Lag” when moving away from a stop. MULTIPLE LAUNCH RPMS The purchase of an IE DSG file grants you access to customization of launch points. With several launch points to choose from you can pick what works best for your setup! KICK DOWN REMOVED IN TIPTRONIC/MANUAL MODE The kick down switch is disabled in manual shift mode, ensuring you stay in the gear you’ve selected, even during hard launches or over bumpy terrain FLAWLESS OPERATION WITH IE ECU TUNES The IE DSG Tune and ECU Tune were developed side by side on our in-house dynamometer. By running both tunes you will unlock the full potential of your 2.0 TSI engine and transmission. VEHICLE FITMENT VW - MK6 GTI 2010-2014 (MK6) 2.0T EA888 Gen1/2 TSI engines VW - MK6 Jetta 2011-2013.5 (MK6) 2.0T EA888 Gen1/2 TSI engines* VW - MK6 GLI 2011-2013.5 (MK6) 2.0T EA888 Gen 1/2 TSI engines* AUDI - TTS 2008-2015 (8J) 2.0T TFSI EA113 engines *This DSG calibration is for 2.0T TSI EA888 Gen 1 & 2 engines only. Many Jetta and GLI models are equipped with a new engine variation (EA888 Gen 3) after 2013.5 and later. This tune does NOT support Gen 3 model engine TCUs. Please verify if your engine is an EA888 Gen 1/2 2.0T TSI or EA888 Gen 3 2.0T TSI tune before ordering. IE DSG tunes are available only for vehicles equipped with 6 speed DSG (DQ250) transmissions. Does not function with manual 6-speed transmission cars.