Volkswagen - Forge Motorsports - Leyo Motorsport - Integrated Engineering

Product Description

• Direct OEM replacement
• Made from the highest quality Aircraft quality T6061 billet aluminium construction
• Fully compatible with OEM electronics
• Fully serviceable piston
• Capable to 600HP (with uprated spring kit)
• Utilising world leading springs for more precise operation and consistency
• All internal and external components have been made in the UK
• Pistons use heat stabilised Viton O-rings
• Lubricated with high temperature Mobil1 grease
• Fully serviceable and rebuildable in minutes
• Unlike other valves on the market, ours produce no check engine lights (EML)
• Improved dynamic throttle response
• Consistent turbo boost & reduced turbo lag
• Covered by the Forge Lifetime Warranty*

This valve is designed to fit the FSI and TSI engines of the VAG group (VW, Audi, Seat, Skoda) listed below, including the 2011-2013 2.0l engine using the IHI Turbo.

• 1.4T (with additional fitting kit FMBGFK3)
• 1.8T
• 2.0T

Note: This will ONLY fit the 1.4 turbo engines up to early 2013, where the turbo is mounted at the front of the engine bay. It will not fit engine codes CMBA & CXSB. We designed the slots in the body to cover a large surface area, allowing for a quick release of air, resulting in a unique sounding dumpvalve.

 

This upgrade/replacement for your original equipment valve integrates seamlessly with the OEM electronics. Using a wiring harness and solenoid, both tested for each specific application, you can confidentially fit a Forge part knowing that there will be no fault codes, check engine lights, or performance issues with the vehicle!

Another particularly unique feature of this product is the included intake manifold tap used to source a vacuum reference for the operation of the valve. This piece also has two other available provisions from which an intake manifold reference can be taken. These extra manifold references can be used for a boost gauge signal, and even a water/meth injection trigger where applicable.

The OEM valve uses a rubber diaphragm and a plastic housing. Both of these materials, but especially the rubber is prone to failure. The rubber can stiffen and go brittle due to the heat from the engine, resulting in diaphragm splitting and boost leak.

Our valve uses full billet alloy construction with a piston based internal design, meaning the issues with the OEM can never happen with ours! To give you even more peace of mind, we made the internals of our valve serviceable. We recommend doing this every 3 years or 20,000 miles, whichever comes first. However, if you don’t want to service your valve yourself you can order the kit and ship your valve back to us and we will carry out the service free of charge! Simply contact us to arrange the service!

The OEM valve internals can also fail if you have your vehicle mapped as the rubber diaphragm is not always strong enough to cope with the increased boost pressure. We build our valves with a spring matched to the original pressure of the car, but include in the kit a spring strong enough to cope with a stage one remap. If you decide to increase the power even more you can guarantee the reliability of our valve by using this spring tuning kit!

This valve was designed by our highly skilled engineers using CAD software to ensure that it will fit with every listed compatible vehicle with ease! 

It is particularly well suited to the B7 and B8 chassis Audi A4 and A5 with the 2.0T engine. The valve mounting location on these vehicles is positioned particularly close to the frame rail of the chassis. Compared to competitors our valve has a much shorter overall installed height.

The OEM part numbers we have replaced with our valve include:

• 06H145710B
• 06H145710C
• 06H145710D
• 06H145710F
• 06H145710G

The Integrated Engineering MK5/MK6 FDS intercooler system was built from the ground up to offer the ultimate in performance for your vehicle. When increasing the power output of your engine it is extremely important to ensure it has the proper cooling to match. It packs a very large intercooler core into the space available, a full 54% larger than the OEM core. This large core delivers cool air to the engine under all circumstances, increasing power and torque and simultaneously reducing heat soak.  

 • 76mm (3 inch) tubing replaces restrictive 60mm factory tubing

 • Bolt on fitment - no hassle or poorly fitting parts when you choose IE

 • Constructed of 304 stainless long-lasting and high-quality material

 • Thick turbo flange - prevents leaks and warping

 • High flow 200 cell catalytic converter - full power with reduced pollution and smell

 • OEM style flex section - allows for more adjustment and won’t fail

 • All inclusive kit - downpipe, midpipes, all hardware

 • TIG welded construction - equates to long lasting welds that are less likely to fail

Product Description

• Direct OEM replacement
• Made from the highest quality Aircraft quality T6061 billet aluminium construction
• Fully compatible with OEM electronics
• Fully serviceable piston
• Capable to 600HP (with uprated spring kit)
• Utilising world leading springs for more precise operation and consistency
• All internal and external components have been made in the UK
• Pistons use heat stabilised Viton O-rings
• Lubricated with high temperature Mobil1 grease
• Fully serviceable and rebuildable in minutes
• Unlike other valves on the market, ours produce no check engine lights (EML)
• Improved dynamic throttle response
• Consistent turbo boost & reduced turbo lag
• Covered by the Forge Lifetime Warranty*

Forge Motorsport were the OG’s of this original groundbreaking design, and we still lead the marketplace with customer service and after care with this innovative blow off valve - Often copied never bettered

This is our piston version of our very popular solenoid driven valve for the 2013-on VAG 1.8 TSI/TFSI engine (US codes CPKA and CPRA) and 2.0 TSI/TFSI engine (Euro code CNTA, CHHA, CHHB, CHHC, CZPA, CJXB and CJXC;US codes CPLA and CPPA)  including Golf MK7 R. This valve is a full replacement atmospheric blow-off valve (i.e. noisy) that integrates seamlessly with the OEM electronics and results in no detriment in performance, and absolutely NO fault codes or check engine lights, which isn’t something that can be said of our competition!

Not only do you get the famous Forge blow off valve sound but this valve also increases the throttle response during gear changes by reducing turbo lag. It has been designed to help the turbocharger maintain its rotational speed ready for when you accelerate, whilst also taking the strain away from the impeller. Without removing this stress from your turbo, it could cause premature failure, especially on tuned engines and modified vehicles.

Like our full replacement recirculating valve option, this valve is fully engineered to remedy the failure issues experienced with the OEM solenoid valves when their diaphragm may rupture which results in a boost leak. The later revision OEM valves have a longer lift but ultimately the plastic brittles and in extreme circumstances, parts of the plastic can break off. Our valve uses full billet alloy construction with a piston based internal design that provides for significantly improved reliability over the OEM valves along with lightning-fast response. It has also been proven in cars running over 600bhp!

This valve has a very short overall installed height, which enables fitment of this atmospheric valve into the tight space between the turbo and the inlet hose from the airfilter, older larger valves and sandwich plates will not fit this engine.

⭐ Great product! Fits perfect and sounds beautiful! 10/10 ⭐

⭐  Fitted the blow of valve today! Works and sounds perfect, not to mention the great customer service to make sure I ordered the correct one ⭐

⭐  Easy installation and sounds fantastic! Money well spent ⭐

In The Box:
1 x FMDVMK7A Valve
1 x Wiring Harness
1 x Solenoid, Bracket, and Screws
1 x Uprated Blue Spring
10 x Cable Ties
1 x 1000mm of 4mm Vacuum Tube
1 x 5mm T Piece
1 x Instructions
1 x Forge Keyring and Sticker

 

When you begin modifying your VW MK7/Audi MK3 Golf R, GTI, A3, or S3 it will become necessary to upgrade the intercooler. Once upgrades such as ECU tuning, exhaust systems, and turbo upgrades are introduced, intake air temperatures begin to rise, resulting in massive power loss.

Description:

The IE Catted Cast Downpipe for VW & Audi MQB incorporates the best of all worlds. Cast bend sections enable the highest flow and best fitment possible. Impressive performance gains will be realized when used with an IE stage 2 ECU tune. Lastly, the aggressive sound from an unrestricted exhaust system is guaranteed to be music to your ears. Product Features • Proven performance gains • 76mm (3 inch) tubing replaces restrictive 60mm factory tubing • Bolt on fitment - no hassle or poorly fitting parts when you choose IE • Constructed of 304 stainless piping - long-lasting and high-quality material • Thick turbo flange - prevents leaks and warping • High flow 200 cell catalytic converter - full power with reduced pollution and smell • Metal matrix catalytic structure - • OEM style flex section - allows for more adjustment and won’t fail • All inclusive kit - downpipe, mid pipes, all hardware • TIG welded construction - equates to long-lasting welds that are less likely to fail • Install instructions - available by CLICKING HERE MQB PERFORMANCE DOWNPIPE OVERVIEW When upgrading your VW MK7 or Audi 8V A3 to stage 2 software you will also need to reduce the back pressure caused by the small diameter stock pipe. With the exhaust system flowing better performance gains be achieved. Turbo lag should also be reduced as an added benefit. IE engineers guarantee a perfect fit by designing all IE downpipes in-house using the latest technology. Digital scanning is using to scan the entire environment which ensures that there is proper clearance and that all mounting points are in the correct location. Manufactured from 304 stainless offers a life-long product that brings performance and fun to the table for years to come. POWER GAINS The most power gains will be achieved when the IE Downpipe is paired with IE matching software, air intake, and FDS intercooler. SOUND TUNING An aggressive and drone-free sound will be emitted from the IE Cast Downpipe. This should be music to your ears! Thick wall tubing and cast sections remove much of “tinny” sound emitted by cheaper, thin wall, downpipes. With downpipes, you get what you pay for in terms of sounds and overall manufacturing quality. HIGH-FLOW CATALYTIC CONVERTER IE’s performance downpipe includes a high-flow 200 cell per inch metal matrix catalyst located as close to the turbo as possible. Metal matrix catalysts are higher performance because the matrix web is thinner, allowing higher flow in the same size. Our catalyst is also a very large diameter, allowing a large flow area and maximum power. By being placed close to the turbo, emissions and unwanted unpleasant smells are greatly reduced. DIRECT BOLT-ON WITH PERFECT FITMENT The IE downpipe replaces over 6 feet of restrictive factory exhaust tubing, all the way back to the OE “Cat-Back” rear section. Sturdy fabricated mounts and precise engineering result in a rattle free and long last replacement exhaust system. 3D scanning systems were employed to ensure perfect placement both in pre and post-production phases. INSTALLATION Installation should be completed by a professional and preferably on an auto lift. CLICK HERE to view and download the install guide. *This product is not CARB certified and thus is not available for purchase in the state of California. VEHICLE FITMENT Audi - A3 MK3/8V 1.8T & 2.0T engines (FWD only)* VW - GTI MK7 2.0T engine VW - GTI MK7.5 2.0T engine VW - Golf MK7 1.8T & 2.0T engine (FWD only)* VW - Golf MK7.5 1.8T & 2.0T engine (FWD only)* *This downpipe system includes a mid pipe that is specially designed to fit Gen 3 1.8T and 2.0T engines in front-wheel drive (FWD) vehicles only. All-wheel drive (AWD) Quattro, or 4 Motion vehicles require a different mid pipe section included in our AWD MQB downpipe kit IE Part Number: IEEXCI1. Please verify if your vehicle is AWD or FWD before ordering. ADDITIONAL REQUIRED MODIFICATIONS Installing a downpipe to your Gen 3 1.8T or 2.0T vehicle requires a matching stage 2 ECU tune to operate properly.