EXPLORE WITH CONFIDENCE

Upgrading your IE 5" velocity stack intake with our harsh climate filter kit will further keep your engine safe when traveling on dirt roads, sandy beaches, or anywhere with dusty contaminants in the air. 

KIT DETAILS

This complete filter kit uses a 3 step approach to combat harsh climates. The filter has been increased from a 6 pleat construction to 8 pleats to increase cotton density. The cotton pleats are then treated with a penetrating filter oil to further catch and trap particulates. As a final measure, a pre-filter sock adds a final layer of protection over the filter. Together, these 3 barriers offer superior filtration for your intake system over our standard performance air filter.

KIT CONTENTS:

• 1X IE oiled 8 pleat density performance 5" filter
• 1X IE pre-filter intake sock
• 1X Air filter worm clamp 

RECHARGING

As the air filter does its job of effectively catching more particulates, eventually it will have to be cleaned and maintained. We recommend washing your cotton filter in water with a little Dawn dish soap, rinsing thoroughly, and allowing it to completely air dry. To replace the oil, any off-the-shelf filter oil kit from your local auto parts supply chain can be used. Do not over-oil the filter, a little goes a long way. 

COMPATIBLE INTAKES

Our 5" Harsh Climate Oiled Air Filter & Sock Upgrade Kit is a direct replacement filter for all popular IE air intake kits with a 5" velocity stack. 

• IEINCI11 - IE MQB 2.0T/1.8T Gen 3 Cold Air Intake
• IEINCK3 - IE Carbon Fiber Intake System For Audi B9 S4 & S5 3.0T
• IEINCG2A - IE Audi 3.0T Cold Air Intake For B8/B8.5 S4 & B8.5 S5
• IEINCN1 - IE Audi 3.0T Cold Air Intake For C7 A6 & A7
• IEINSG1 - IE Audi 3.0T Cold Air Intake For 8R SQ5 & Q5
• IEINCG1 - IE Audi 2.0T TSI Cold Air Intake For B8/B8.5 A4 & A5
• IEINCK1 - IE Audi B9 A4 & A5 Cold Air Intake
• IEINCW1 - IE Cold Air Intake System For VW MQB Tiguan 2.0T
• IEINCV1 - IE Performance Intake System For VW Atlas 2.0T
• IEINCC2 - IE 2.0T TSI Cold Air Intake For VW MK5, MK6 GTI, Jetta, CC & 8P A3
• IEINCB4 - IE 2.0T FSI Cold Air Intake Kit For MK6 Golf R, A3, MK5 GTI, Jetta
• IEINCC4 - IE Gen 3 2.0T/1.8T Cold Air Intake For 2013-2018 MK6 Jetta & GLI
• IEINCJ1 - IE  Carbon Fiber Intake For Audi TTS MK2
• IEINCI4 - IE VW 1.4T Cold Air Intake For VW MK6 Jetta

Description

VW MK7/MK7.5 & AUDI 8V 2018+ DSG TUNE Don't short shift your ECU tune and performance parts, get the most out of your modifications with the IE DSG Transmission tune for 2019+ GLI, GTI, Golf R, A3, S3 2.0T. Instantly gain increased power, higher RPM limit, faster shifts, optimized shift points, and a true performance tuned transmission. Acceleration times will greatly improve transforming your 2.0T into a fully rounded performance monster. DSG TUNE FEATURES Required for high torque IE ECU tunes Lightning fast gear shifts Kick down in manual mode eliminated Lag time reduced when starting off in first gear Drive shift mapping entirely reworked with an enthusiast in mind Flashed directly through OBD-II Port (No TCU removal required) Increased clutch pressure on tap for higher torque without slip Temperature protection remains for safety Gear hunting reduced Gearbox “Torque Limiters” removed REQUIRED FOR SELECT ECU TUNES Required for GLI, GTI, Golf R, A3, & S3 Stage 1 high torque and all Stage 2 tune files, your new transmission tune will no longer lug the engine in drive mode, or short shift the larger powerband. Clutch clamping forces are increased so the transmission can safely handle and deliver the increased power and torque. To get the most out of your tune investment, a lot of features have been added to make a fully rounded performance vehicle with more aggressive launches, faster shifting, higher RPM, and optimized shift points. DSG tune requires a matching ECU Tune, do not install on stock ECU tunes. ALL INCLUSIVE DSG FILE, NO STAGES That's right, your IE DSG tune is all-inclusive and does not offer expensive "Stage" upgrades. All features for any ECU stage are included in the tune and will never require unnecessary upgrade charges. IE POWERlink DIRECT PORT FLASH TOOL IE's POWERlink direct port flash tool is required to flash your ECU (engine control unit) or TCU (transmission control unit) and is available separately. The POWERlink tool is sold with all new IE ECU tunes and can also be used to flash your new DSG tune. If you already own an IE POWERlink unit, purchasing this file will add the credits to your cable within one working day. If you do not own a POWERlink cable, please chose to add one in the drop-down menu above. POWERlink FEATURES: FILE SWITCHING The POWERLink cable allows for map switching without making a trip back to an IE Software dealer. EASY OPERATION Simply plug your IE PowerLink cable into your vehicle’s OBD-II port and the USB port on your Windows-powered laptop to use the included IE Flash Wizard software. The flash wizard will then walk you through the installation steps. FLASH MULTIPLE CARS Have a friend with a compatible VW or Audi? Share the power with up to 5 different cars with a single cable. Just add enough credits to your cable for the desired tune and power-up your entire crew. RETURN TO STOCK ANYTIME With the IE PowerLink, you can return your vehicle back to original ECU or TCU programming at any time. EASY UPDATES IE will always provide free software updates as they become available and easily reflashed through your IE PowerLink cable. SYSTEM REQUIREMENTS Laptop or tablet with Wifi connection and USB port running Windows 7 or newer operating system required. Powered by 32 or 64-bit processor with 1.0GHz or greater and 4GB of Ram. Windows NT not supported. IE DSG TUNE TECHNICAL FEATURES HIGHER SHIFT POINTS Utilize the whole powerband of your turbocharged Gen 3 TSI with IS20 Turbo engine without the DSG interfering and shifting early. DRIVE MAPPING REWORKED The MQB 2.0 TSI DSG is designed to a fault to keep engine rpm extremely low in drive. We completely reworked this, creating a more enthusiast-friendly drive mapping which shifts a bit higher. This eliminates vibration and that constant feeling that you’re lugging the engine. We’ve reworked the downshifting aspect as well, making the transmission much quicker to deliver power when you need it. Thousands of miles of testing were accumulated and a variety of users were polled to come up with this improved drive mode. INCREASED CLUTCH PRESSURE Increasing the clutch pressure allows for the transmission to hold more torque without causing clutch damage or expedited wear. With the increased torque, the acceleration will be greatly increased and launches will far more aggressive. FLASHED THROUGH OBD-II PORT There’s no need to remove the TCU from the car and it can be flashed in your driveway or through an IE software dealer. Additionally, having an IE PowerLink cables means you can install updates are they become available as well as read TCU and ECU fault codes. TAKE-OFF LAG REDUCED The clutch engagement has been reworked to reduce that annoying “DSG Lag” when moving away from a stop. KICK DOWN REMOVED IN MANUAL MODE The kick down switch is disabled in manual shift mode, ensuring you stay in the gear you’ve selected, even during hard launches or over bumpy terrain FLAWLESS OPERATION WITH IE ECU TUNES The IE DSG Tune and ECU Tune were developed side by side on our in-house dynamometer. By running both tunes you will unlock the full potential of your 2.0 TSI Gen 3 engine and transmission. VEHICLE FITMENT VW - GTI 2019+ (MK7.5) W/DSG TRANSMISSION VW - GLI 2019+ (MK7) W/DSG TRANSMISSION VW - GOlf R 2018+ (MK7.5) W/DSG TRANSMISSION AUDI - A3 2019+ (8V) W/ DSG TRANSMISSION AUDI - S3 2018+ (8V) W/ DSG TRANSMISSION

Product Description

This will replace OEM part numbers 06H 145 710D, 06F 145 710G, & 06H 145 710 C

Forge Motorsport is proud to release the latest version of our very popular solenoid driven valve for the 2013-on VAG 1.8 TSI/TFSI engine (US codes CPKA and CPRA) and 2.0 TSI/TFSI engine (Euro code CNTA, CHHA, CHHB, CJXB, CZPA, and CJXC;US codes CPLA and CPPA) including Golf MK7 R

This valve is fully engineered to remedy the failure issues experienced with the OEM solenoid valves when their diaphragm may rupture which results in a boost leak. The later revision OEM valves have a longer lift but ultimately the plastic brittles and in extreme circumstances, parts of the plastic can break off. Our valve uses full billet alloy construction with a piston based internal design that provides for significantly improved reliability over the OEM valves along with lightning fast response. It has also been proven in cars running over 600bhp!

This new valve has a very short overall installed height, which enables fitment of this atmospheric valve into the tight space between the turbo and the inlet hose from the airfilter, older larger valves and sandwich plates will not fit this engine.

We recommend servicing your valve every 3 years, or 20,000 miles, whichever comes sooner

In The Box:
1 x FMDVMK7R Valve
1 x Wiring Harness
1 x Solenoid, Bracket, and Screws
1 x Uprated Blue Spring
10 x Cable Ties
1 x 1000mm of 4mm Vacuum Tube
1 x 5mm T Piece
1 x Instructions
1 x Forge Keyring and Sticker

Product Description

This is a direct replacement for Part Number 06H 131 111. - It will fit EA888 Gen 3 engine with IHI Turbo IS20 IS38

On a 2.0L Porsche Macan, this muffler delete gave an additional 10bhp during dyno tests.

Forge has developed this turbo outlet muffler delete pipe for the 1.8 and 2.0 petrol turbo (TSI) (EA888 engine). It has been designed with 3 points of contact to eliminate any possibility of resonation. This part will improve the sound of your turbo spooling and improve response due to its sleek single billet design that eliminates the restriction and turbulence caused by the OEM part.

Product Description

The Forge Motorsport Turbo Blankets are designed to isolate the radiant heat produced by the turbocharger. Designed by the Forge development team for the EA888 TSI vehicles, the Forge turbo blanket is designed to assist in the protection and prolonged life of the engine components.

·       Stainless Steel Rivets
·       Stainless Steel Fasteners
·       Carbon fabric Outer Shell
·       Calcium Magnesium Silicate Wool constructed Inner Core
·       High temperature silica fabric

The unique design will assist in reducing turbo lag and produce cooler air intake temperatures, The Forge turbo blanket will lose its flexibility over the first few heat cycles as the material cures, so once fitted it should not be routinely removed as you will likely damage the blanket.

Design innovation keeps the heat of the exhaust gases contained within the hot side of the turbocharger, away from the cool side and the intake path. More oxygen per unit volume reaches the engine, therefore giving more power. This product also fits the vehicles with the following turbochargers:

• T4
• T5
• T25
• The Garrett GTX28 and GTX30 Range
• Borg Warner EFR6258

Interior Surface:

·       Max Temperature Rating: 2300°F/1260°C
·       Continuous Use Limit: 1832°F1000°C

Exterior Surface:

·       Direct Contact Limit: 1800°F/982°C
·       Radiant Heat Limit: 2500°F/1371°C

Complimentary Products

Product Description

THIS PRODUCT DOES NOT FIT LEFT HAND DRIVE VEHICLES

The Forge Motorsport high flow intake hose for the MQB platform 2.0 engines, eliminates the highly restrictive plastic inlet pipe, and replaces it with our smooth bore multi-ply silicone hose which increases air flow, improving efficiency and performance. This equates to increases of up to 10hp which is a remarkable gain for an easy to fit bolt on modification.

⭐ Excellent quality product & easy to fit ⭐

The high flow male alloy coupler is a bayonet type, rotated to the locked position before fixing in place by positioning the hose on the alloy coupler and tightening the hose clamps at both ends of the hose, anchoring the alloy coupler in position to complete the installation.

The Forge silicone hose in this kit has been designed to include an expensive inner liner of modified silicone known as Fluorosilicone.This means the hoses are suitable to be used with either modern long-life coolants, Organic Acid Technology coolants (O.A.T.) but more importantly for this application, air containing oil mist. The construction of the hoses has been engineered to exceed that of the OEM fitments, and will enhance any engine bay both technically and aesthetically.The use of a Fluorosilicone liner ensures that Forge silicone hoses are the clear market leader.

As with all Forge products, this hose comes with a lifetime warranty*