Fits 1.4T, 1.8T & 2.0T FSI and TSI engines, including the late 2011-2013 2.0 engine fitted with the IHI turbo, (the 1.4T needs additional fitting kit FMBGFK3)
We recommend servicing your valve every 3 years, or 20,000 miles, whichever comes sooner
Forge Motorsport offer this valve option for the 1.4T, 1.8T & 2.0T FSI and TSI engines, including the late 2011-2013 2.0 engine fitted with the IHI turbo, (the 1.4T needs additional fitting kit (FMBGFK3) found in a wide range of vehicles from VW, Seat, Skoda and Audi.
This valve represents the latest evolution of part number FMFSITVR, The result is a full replacement recirculating valve that integrates seamlessly with the OEM electronics and results in absolutely no fault codes, no check engine lights, and no detriment to the performance of the vehicle in any way. Like our full replacement atmospheric valve option, the FMFSITVR and FMFSITAT is fully engineered to remedy the failure issues experienced with the OEM solenoid valves when their diaphragm may rupture which would effectively result in a boost leak.
Our valve uses full billet alloy construction with a piston based internal design that provides for significantly improved reliability over the OEM valves along with lightning fast response. This valve is particularly well suited to the B7 and B8 chassis Audi A4 and A5 with the 2.0T engine. The valve mounting location on these vehicles is positioned particularly close to the frame rail of the chassis, and the overall installed height of our standard replacement valve and spacer combination is such that it conflicts with the chassis at this location.
The FMFSITVR valve has a much shorter overall installed height, which enables fitment of this recirculating valve option onto the B7 and B8 chassis whereas this was previously not an option. Another particularly unique feature of this product is the included intake manifold tap used to source a vacuum reference for the operation of the valve. This piece also has two other available provisions from which an intake manifold reference can be taken. These extra manifold references can be used for a boost gauge signal, and even a water/meth injection trigger where applicable. If this to be installed to the 1.4 Turbo engine, it will be necessary to additionally purchase our boost sensor adaptor FMBGFK3 - please see below in Related Products.
Note: This will ONLY fit the 1.4 turbo engines up to early 2013, where the turbo is mounted at the front of the engine bay. It will not fit engine codes CMBA & CXSB
In The Box:
1 x FMFSITVR Valve
1 x Wiring Harness
1 x Solenoid, Bracket, and Screws
1 x PCV Adaptor Kit
1 x Blue Spring (Uprated)
10 x Cable Ties
1 x 2000mm Length of 4mm Vac Hose
1 x Instruction Booklet
1 x Forge Keyring and Sticker
If you are unsure if this product is suitable for your application, please contact us.
Regular Price: $399.00
Special Price $339.00
The massive 5” velocity stack and ram-air designed IE Cold Air Intake Kit delivers the most air and horsepower possible. Quickly add horsepower, torque, and aggressive engine and turbo sound to your VW or Audi 2.0T TSI (Gen1/2) engine.
Feed your 2.0T TSI GTI, Jetta, GLI, CC, or A3 with a supply of cold air with this direct-fit high-flow cold air intake kit. This intake features a generously-sized inlet pipe that connects to the OE mass air flow (MAF) sensor. The MAF sensor receives high-velocity air fed directly from a 5" bellmouth. Our high-flow bellmouth is neatly housed in a heat shield, which separates the air filter from the hot under-hood air, allowing only cold air to be drawn into the turbo inlet directly from the front of the car.
This air intake kit provides all the necessary piping and couplers to plumb the intake system from the turbo to the MAF and then to the heat shield. The heat shield installs using the OE grommets for easy maintenance and reliable mounting with no rubbing or interference with other factory parts.
The air intake utilizes a high-flow bellmouth behind the air filter to deliver as much air as possible. This bellmouth design increases the air velocity to the MAF and pulls cold air equally from all directions into the filter. This bellmouth is securely fastened to the heat shield as a clean pass-through providing a solid mount for the air filter and turbo inlet pipe. You have no worry about the intake pipe moving around and causing damage unlike other intake kits on the market, which simply clamp the filter onto the end of the inlet pipe or MAF. Furthermore, the bellmouth opening allows for a filter with a very large surface area that can support any horsepower goal. The same filter and bellmouth design have been tested to support over 500HP!
The IE heat shield is designed to create a thermal barrier blocking all of the radiant heat from the engine bay. Only cold air from the front of the vehicle is drawn into the filter from the opening in the radiator support keeping air intake temperatures as cold as possible. This allows factory placement of the intake to be used without placing the filter lower in the vehicle where it can be subjected to engine harming road debris or fluid.
The MK5/MK6 2.0T TSI engine has two different engine codes. CBFA engine codes are equipped from the factory with a secondary air injection (SAI) pump that connects to the factory intake box. These engines require a small breather filter for this SAI line when installing an aftermarket intake. CCTA engine codes do not have this SAI pump and will not require this filter. Identify your engine code using the photos below, and add an SAI filter kit above if needed when ordering your intake.
Installation is quick and easy to install with basic tools. The process should take around an hour for most enthusiasts.
CLICK HERE to view and download the Cold Air Intake install guide
Regular Price: $769.00
Special Price $719.00
Add serious power and fun to your car without popping the hood! The IE POWERlink V4 Flash Cable is the key to uploading IE engine-specific tuning upgrades to your ECU, Simply plug into your vehicles OBD2 port and launch the app on your Apple or Android phone (or Windows laptop). Enjoy serious horespower, torque gains, increased acceleraton, faster 0-60 times, optimized drivability, improved responsiveness, multiple octanes, enthusiast drive mapping and more in only minutes!
Would rather use a laptop? No problem! IE Flash Wizard Software allows the IE POWERlink Tool to communicate with your vehicle’s ECU to flash software tunes, upgrade, update, data log, or read/write codes on any Windows 10+ powered laptop or tablet.
DEVICE | PORTS | OS | PROC. | POWER | RAM |
Laptop or Tablet |
Wifi & USB |
Windows 10 or newer |
32 or 64 bit |
1.0ghz or greater |
4GB or greater |
NOTE: Mobile flashing app requires an IE V4 POWERlink flashing cable and is not compatible with older V3 serial number units. Have a V3 and ready to go Mobile? Simply purchase a new V4 POWERlink to gain full mobile functionality.
Regular Price: $769.00
Special Price $692.00
Regular Price: $929.00
Special Price $875.00
.
XFORCE FOR VOLKSWAGEN GOLF GTI MK6 & SCIROCCO R! AVAILABLE NOW.
Regular Price: $1,300.00
Special Price $1,145.00
XFORCE - MK6 GTI Dump Pipe & Cat Features:
-T304 Seamless Stainless Steel tubing
-T304 Stainless Steel flanges
-Fixed 200 cell cat
-100% TIG Welded
-T304 Stainless Steel 02 bungs
-Stainless Steel Clamps
-Great Sound
Proper software must be used to remove the CEL that will occur.
COMPATIBLE WITH FACTORY VW CATBACK SYSTEMS
Regular Price: $950.00
Special Price $835.00