One of the most common failures on the 2.0T FSI engine is the factory pressure-relief valve. These valves are in place to recirculate crankcase gases into the intake manifold once they open. Although this works fine for a few thousand miles, they begin to leak over time and cause boost to go past the valve into the valve cover. This not only causes an oily mess in the engine bay from crankcase pressure, but a rough idle, fuel economy decline and boost loss. With boost pressure far below where it should be, it is common to notice significant power losses and poor drivability.
Regular Price: $184.00
Special Price $179.00
EVAP Crossover Tube Relocation Kit for 2.0T FSI with IE Valve Cover
Description:
Made from T6061 billet aluminum, LEYO DSG Oil Filter Housing not only adds aesthetic appeal to the engine bay, but specially designed fin also provides effective heat dispersion for the DSG under load. Heat resistant to prolong optimum operational temperature.
*Only fits 6 speed DSG DQ250 wet.
Specifications:
T6061 Billet aluminum construction.
Hard coat anodized finish for impeccable appearance and heat resistance.
Promotes oil heat dispersion.
The massive 5” velocity stack and ram-air designed IE Cold Air Intake Kit delivers the most air and horsepower possible. Quickly add horsepower, torque, and aggressive engine and turbo sound to your VW or Audi 2.0T TSI (Gen1/2) engine.
Feed your 2.0T TSI GTI, Jetta, GLI, CC, or A3 with a supply of cold air with this direct-fit high-flow cold air intake kit. This intake features a generously-sized inlet pipe that connects to the OE mass air flow (MAF) sensor. The MAF sensor receives high-velocity air fed directly from a 5" bellmouth. Our high-flow bellmouth is neatly housed in a heat shield, which separates the air filter from the hot under-hood air, allowing only cold air to be drawn into the turbo inlet directly from the front of the car.
This air intake kit provides all the necessary piping and couplers to plumb the intake system from the turbo to the MAF and then to the heat shield. The heat shield installs using the OE grommets for easy maintenance and reliable mounting with no rubbing or interference with other factory parts.
The air intake utilizes a high-flow bellmouth behind the air filter to deliver as much air as possible. This bellmouth design increases the air velocity to the MAF and pulls cold air equally from all directions into the filter. This bellmouth is securely fastened to the heat shield as a clean pass-through providing a solid mount for the air filter and turbo inlet pipe. You have no worry about the intake pipe moving around and causing damage unlike other intake kits on the market, which simply clamp the filter onto the end of the inlet pipe or MAF. Furthermore, the bellmouth opening allows for a filter with a very large surface area that can support any horsepower goal. The same filter and bellmouth design have been tested to support over 500HP!
The IE heat shield is designed to create a thermal barrier blocking all of the radiant heat from the engine bay. Only cold air from the front of the vehicle is drawn into the filter from the opening in the radiator support keeping air intake temperatures as cold as possible. This allows factory placement of the intake to be used without placing the filter lower in the vehicle where it can be subjected to engine harming road debris or fluid.
The MK5/MK6 2.0T TSI engine has two different engine codes. CBFA engine codes are equipped from the factory with a secondary air injection (SAI) pump that connects to the factory intake box. These engines require a small breather filter for this SAI line when installing an aftermarket intake. CCTA engine codes do not have this SAI pump and will not require this filter. Identify your engine code using the photos below, and add an SAI filter kit above if needed when ordering your intake.
Installation is quick and easy to install with basic tools. The process should take around an hour for most enthusiasts.
CLICK HERE to view and download the Cold Air Intake install guide
Regular Price: $769.00
Special Price $719.00
Regular Price: $769.00
Special Price $692.00
Regular Price: $929.00
Special Price $875.00
Replace your restrictive factory airbox with this new airbox from Leyo Motorsport. Meticulously engineered, this final design is the culmination of numerous air flow rendering and analysis.
High flow air filter ensures maximum air flow eliminating the air flow restrictions found in the stock airbox. More air means more usable power especially when paired with Leyo charge pipe for the MK7 1.4.
Installation is simple and straightforward, in just minutes your engine bay will be transformed with the addition of this Leyo intake kit.
*This product is only for use on the race track.
Specifications:
Track and dyno proven for greater horsepower gain.
Maximum airflow.
Unique quality and design.
Simple installation.
Description:
Leyo Motorsport dual port boost tap system plugs directly into the intake manifold and makes several configuration options available. Makes anything for your boost reference, such as boost gauges, bov & etc. It will also maintain OEM PCV system function.
Specifications:
Machined billet Aluminum T6061.
Dual Port Design for multiple boost reference.
Direct bolt on easy Installation.
Dual leak free O-ring.
Description
Stand out from the crowd.
Dare to be different.
Simple yet sophisticated look.
Quick n Easy install.
Stylishly elegant.
Run out of things to mod.
Cleaner than your ex-girlfriend.
Adds 10HP to your key.
For 2015+ VW MQB Platform 3-button & flip blade key ONLY.
Please check your car key before purchasing.
INCLUDED
LEYO CLEAR KEY BASE x1
OEM CLEAR KEY BASE x1
TORX SCREWDRIVER x
OPEN
REMOVE
INSTALL
DONE