Scirocco - Forge Motorsports - Integrated Engineering - Whiteline

Product Description

• Direct OEM replacement
• Made from the highest quality Aircraft quality T6061 billet aluminium construction
• Fully compatible with OEM electronics
• Fully serviceable piston
• Capable to 600HP (with uprated spring kit)
• Utilising world leading springs for more precise operation and consistency
• All internal and external components have been made in the UK
• Pistons use heat stabilised Viton O-rings
• Lubricated with high temperature Mobil1 grease
• Fully serviceable and rebuildable in minutes
• Unlike other valves on the market, ours produce no check engine lights (EML)
• Improved dynamic throttle response
• Consistent turbo boost & reduced turbo lag
• Covered by the Forge Lifetime Warranty*

This valve is designed to fit the FSI and TSI engines of the VAG group (VW, Audi, Seat, Skoda) listed below, including the 2011-2013 2.0l engine using the IHI Turbo.

• 1.4T (with additional fitting kit FMBGFK3)
• 1.8T
• 2.0T

Note: This will ONLY fit the 1.4 turbo engines up to early 2013, where the turbo is mounted at the front of the engine bay. It will not fit engine codes CMBA & CXSB. We designed the slots in the body to cover a large surface area, allowing for a quick release of air, resulting in a unique sounding dumpvalve.

 

This upgrade/replacement for your original equipment valve integrates seamlessly with the OEM electronics. Using a wiring harness and solenoid, both tested for each specific application, you can confidentially fit a Forge part knowing that there will be no fault codes, check engine lights, or performance issues with the vehicle!

Another particularly unique feature of this product is the included intake manifold tap used to source a vacuum reference for the operation of the valve. This piece also has two other available provisions from which an intake manifold reference can be taken. These extra manifold references can be used for a boost gauge signal, and even a water/meth injection trigger where applicable.

The OEM valve uses a rubber diaphragm and a plastic housing. Both of these materials, but especially the rubber is prone to failure. The rubber can stiffen and go brittle due to the heat from the engine, resulting in diaphragm splitting and boost leak.

Our valve uses full billet alloy construction with a piston based internal design, meaning the issues with the OEM can never happen with ours! To give you even more peace of mind, we made the internals of our valve serviceable. We recommend doing this every 3 years or 20,000 miles, whichever comes first. However, if you don’t want to service your valve yourself you can order the kit and ship your valve back to us and we will carry out the service free of charge! Simply contact us to arrange the service!

The OEM valve internals can also fail if you have your vehicle mapped as the rubber diaphragm is not always strong enough to cope with the increased boost pressure. We build our valves with a spring matched to the original pressure of the car, but include in the kit a spring strong enough to cope with a stage one remap. If you decide to increase the power even more you can guarantee the reliability of our valve by using this spring tuning kit!

This valve was designed by our highly skilled engineers using CAD software to ensure that it will fit with every listed compatible vehicle with ease! 

It is particularly well suited to the B7 and B8 chassis Audi A4 and A5 with the 2.0T engine. The valve mounting location on these vehicles is positioned particularly close to the frame rail of the chassis. Compared to competitors our valve has a much shorter overall installed height.

The OEM part numbers we have replaced with our valve include:

• 06H145710B
• 06H145710C
• 06H145710D
• 06H145710F
• 06H145710G

Product Description

Fits 1.4T, 1.8T & 2.0T FSI and TSI engines, including the late 2011-2013 2.0 engine fitted with the IHI turbo, (the 1.4T needs additional fitting kit FMBGFK3)

We recommend servicing your valve every 3 years, or 20,000 miles, whichever comes sooner

Forge Motorsport offer this valve option for the 1.4T, 1.8T & 2.0T FSI and TSI engines, including the late 2011-2013 2.0 engine fitted with the IHI turbo, (the 1.4T needs additional fitting kit (FMBGFK3) found in a wide range of vehicles from VW, Seat, Skoda and Audi.

This valve represents the latest evolution of part number FMFSITVR, The result is a full replacement recirculating valve that integrates seamlessly with the OEM electronics and results in absolutely no fault codes, no check engine lights, and no detriment to the performance of the vehicle in any way. Like our full replacement atmospheric valve option, the FMFSITVR and FMFSITAT is fully engineered to remedy the failure issues experienced with the OEM solenoid valves when their diaphragm may rupture which would effectively result in a boost leak.

Our valve uses full billet alloy construction with a piston based internal design that provides for significantly improved reliability over the OEM valves along with lightning fast response. This valve is particularly well suited to the B7 and B8 chassis Audi A4 and A5 with the 2.0T engine. The valve mounting location on these vehicles is positioned particularly close to the frame rail of the chassis, and the overall installed height of our standard replacement valve and spacer combination is such that it conflicts with the chassis at this location.

The FMFSITVR valve has a much shorter overall installed height, which enables fitment of this recirculating valve option onto the B7 and B8 chassis whereas this was previously not an option. Another particularly unique feature of this product is the included intake manifold tap used to source a vacuum reference for the operation of the valve. This piece also has two other available provisions from which an intake manifold reference can be taken. These extra manifold references can be used for a boost gauge signal, and even a water/meth injection trigger where applicable. If this to be installed to the 1.4 Turbo engine, it will be necessary to additionally purchase our boost sensor adaptor FMBGFK3 - please see below in Related Products.

Note: This will ONLY fit the 1.4 turbo engines up to early 2013, where the turbo is mounted at the front of the engine bay. It will not fit engine codes CMBA & CXSB

 

In The Box:
1 x FMFSITVR Valve
1 x Wiring Harness
1 x Solenoid, Bracket, and Screws
1 x PCV Adaptor Kit
1 x Blue Spring (Uprated)
10 x Cable Ties
1 x 2000mm Length of 4mm Vac Hose
1 x Instruction Booklet
1 x Forge Keyring and Sticker

If you are unsure if this product is suitable for your application, please contact us.

SHIFT FASTER, DRIVE FASTER The IE DSG Tune for your VW MK6 GTI, Jetta, GLI, or Audi 8J TTS 2.0T delivers increased power, higher RPM limit, faster shifts, optimized shift points, adjustable launch control, and additional transmission performance features when paired with a matching ECU tune. Acceleration times will greatly improve turning your tuned 2.0T TSI into a fully rounded performance monster. LEADING FEATURES Lightning fast gear shifts Higher shift points of 6800 RPM Kick down in manual mode eliminated Lag time reduced when starting off in first gear Multiple launch RPMs: 3200, 3400, 3600, 3800, 4000 Drive shift mapping entirely reworked with an enthusiast in mind Flashed directly through OBD-II Port (No TCU removal required) Works flawlessly with an IE ECU tune Increased clutch pressure on tap for higher torque without slip Temperature protection remains for safety Gear hunting reduced Gearbox “Torque Limiters” removed WHAT DOES A DSG TRANSMISSION TUNE DO? The IE DSG Tune for the MK6 2.0T TSI has been carefully set up to make the car way more fun to drive. It completely reworks the shift point mapping in both drive and sport. The transmission will no longer lug the engine in drive mode. Clutch clamping forces are increased so the transmission can safely handle much more power. Shifts are much, much faster taking time directly off the 0-60 and ¼ mile times. ONE TUNE FOR ALL STAGES IE’s TCU/DSG tune is all-inclusive and does not offer expensive upgrades. That’s right, there are no unnecessary upgrade charges and all features are included from the outset. A great deal of sportiness is added from the tune while maintaining factory smoothness and driveability. More aggressive launches and faster shifts are guaranteed to put a smile on your face. Also, expect acceleration and 0-60 times to improve from faster shifting. DSG tune requires a matching ECU Tune, do not install on stock ECU tunes. USER ADJUSTABLE LAUNCH CONTROL The purchase of an IE DSG file grants you access to customization of launch points. With several launch points to choose from you can pick what works best for your setup! Available Launch Control RPMs: 3200 RPM 3400 RPM 3600 RPM 3800 RPM 4000 RPM IE DSG TUNE TECHNICAL FEATURES HIGHER SHIFT POINTS Utilize the whole powerband of your 2.0 TSI engine without the DSG interfering and shifting early. DRIVE MAPPING REWORKED The MK6 2.0 TSI DSG is designed to a fault to keep engine rpm extremely low in drive. We completely reworked this, creating a more enthusiast-friendly drive mapping which shifts a bit higher. This eliminates vibration and that constant feeling that you’re lugging the engine. We’ve reworked the downshifting aspect as well, making the transmission much quicker to deliver power when you need it. Thousands of miles of testing were accumulated and a variety of users were polled to come up with this improved drive mode. INCREASED CLUTCH PRESSURE Increasing the clutch pressure allows for the transmission to hold more torque without causing clutch damage or expedited wear. With the increased torque, the acceleration will be greatly increased and launches will far more aggressive. FLASHED THROUGH OBD-II PORT There’s no need to remove the TCU from the car and it can be flashed in your driveway or through an IE software dealer. Additionally, having an IE PowerLink cables means you can install updates are they become available as well as read TCU and ECU fault codes. TAKE-OFF LAG REDUCED The clutch engagement has been reworked to reduce that annoying “DSG Lag” when moving away from a stop. MULTIPLE LAUNCH RPMS The purchase of an IE DSG file grants you access to customization of launch points. With several launch points to choose from you can pick what works best for your setup! KICK DOWN REMOVED IN TIPTRONIC/MANUAL MODE The kick down switch is disabled in manual shift mode, ensuring you stay in the gear you’ve selected, even during hard launches or over bumpy terrain FLAWLESS OPERATION WITH IE ECU TUNES The IE DSG Tune and ECU Tune were developed side by side on our in-house dynamometer. By running both tunes you will unlock the full potential of your 2.0 TSI engine and transmission. VEHICLE FITMENT VW - MK6 GTI 2010-2014 (MK6) 2.0T EA888 Gen1/2 TSI engines VW - MK6 Jetta 2011-2013.5 (MK6) 2.0T EA888 Gen1/2 TSI engines* VW - MK6 GLI 2011-2013.5 (MK6) 2.0T EA888 Gen 1/2 TSI engines* AUDI - TTS 2008-2015 (8J) 2.0T TFSI EA113 engines *This DSG calibration is for 2.0T TSI EA888 Gen 1 & 2 engines only. Many Jetta and GLI models are equipped with a new engine variation (EA888 Gen 3) after 2013.5 and later. This tune does NOT support Gen 3 model engine TCUs. Please verify if your engine is an EA888 Gen 1/2 2.0T TSI or EA888 Gen 3 2.0T TSI tune before ordering. IE DSG tunes are available only for vehicles equipped with 6 speed DSG (DQ250) transmissions. Does not function with manual 6-speed transmission cars.

Engineered to 'Activate More Grip', sway bars are principally designed to reduce body roll or sway. By reducing body roll, lateral loads are spread more evenly across the tires thereby increasing cornering grip and improving outright performance. This Whiteline 24mm 3 point adjustable sway bar = more grip = better handling = outright performance - it's the best dollar for dollar handling improvement you can make to your vehicle. In fact, benefits extend to improvements in handling, safety and tyre wear without affecting ride quality or comfort.

Engineered to 'Activate More Grip', sway bars are principally designed to reduce body roll or sway. By reducing body roll, lateral loads are spread more evenly across the tires thereby increasing cornering grip and improving outright performance. This Whiteline 24mm 3 point adjustable sway bar = more grip = better handling = outright performance - it's the best dollar for dollar handling improvement you can make to your vehicle. In fact, benefits extend to improvements in handling, safety and tyre wear without affecting ride quality or comfort.

Whiteline Anti Lift Kits are primarily designed to improve traction and cornering grip under power. By increasing static caster and improving front end geometry the new alloy mounts coupled with low compliance synthetic elastomer bushings serve to dramatically sharpen initial turn-in response and reduce understeer.

A must for lowered vehicles, Whiteline roll centre, bump steer and camber correction kits are designed to correct roll-centre geometry using specially engineered ball-joints. Raising the front roll-centre results in a substantial increase to front roll resistance and a significant reduction in suspension compression of the outside front wheel during cornering. The result is more even weight distribution and improved tyre contact ultimately improving front end grip and cornering speeds.

Soft factory bushings whilst they do a good job of not transmitting engine vibration, they do create vague and unresponsiveness in the vehicles drive train. Under hard acceleration, the engine and transmission rotates, Whiteline's synthetic elastomer torque arm inserts work in conjunction with the OE rubber bushing giving your car better throttle response as well as more crisp and defined gear shifts. Suits both Automatic or manual transmissions .

Not many enthusiasts are aware that OE and more importantly aftermarket sway bar effectiveness can be hindered by worn or inadequate mounts, drop links and lateral stoppers. Whiteline adjustable sway bar links are engineered to be up to the task with top spec, light weight componentry combined with a window of adjustability, eliminating sway bar preload on installation but most importantly ensuring the maximum output of the sway bar for improved grip and better handling.