Search results for 'product'

Product Desciption:

We now offer a MK3 Audi TTRS and 8V Facelift Audi RS3 Catalytic Converter Midpipe kit.

Product Details:

– Hand Crafted from 3″ T304 Stainless Steel

– Necessary installation hardware included (gasket set included)

– CNC water jet cut flanges

– CNC mandrel bent stainless steel piping

– Polished stainless steel exhaust tubing

– Power gains from 7+ whp 10+ ftlbs torque

– Will not cause CEL (check engine light)

When a high-flow catalytic converter or test pipe is used on a late model car it's guaranteed that CEL (Check Engine Light) will come on.

This CEL is caused by a fault code that indicates an inefficient catalytic converter.

Our CEL eliminator is CNC machined in-house from high quality cold roll steel for a long-lasting effective performance.

Install this spacer on your REAR (downstream, post-cat) oxygen sensor to effectively remove the code for catalyst efficiency.

This is recommended for vehicles that do NOT have "stage 2" software.

This product is not intended to and will not provide emissions compliance.

FOR OFF-ROAD USE ONLY!

Emissions laws vary by state and by province. Check local and federal laws before modifying your exhaust system.

Emissions compliance is the sole responsibility of the vehicles owner. This is a universal product that works on variety of vehicles, however it is not effective on all cars.

At CTS Turbo we are proud to announce our new air intake system for the transverse 2.0T FSI EA113 VW/Audi range of vehicles.

The air scoop works in conjunction with our sealed airbox to seamlessly force cold air into our 2.75″ air intake system.  Air then flows through our high flow cone air filter, which utilizes an inverted cone design for maximum engine breathing.  Our CNC mandrel-bent aluminum intake pipe allows for smooth entry of cold air into the engine providing peak power gains ranging from 9-15WHP. By using a factory MAF position, you can be sure that fuel trims will remain perfect.

All of the components included in the CTS air intake system work flawlessly together to provide increased horsepower and torque throughout the entire power band and an aggressive race-inspired sound.

This intake kit is designed to be compatible with our FSI EA113 BOSS kits; intake pipe features 2x 1/8″ bungs and 1x 1/2″ bung for easy installation of BOSS kits. Plugs are included.

Product Details:

• Full 2.75″ Mandrel-bent aluminum piping with black powder coating
• Compatible with CTS BOSS kits, with provisions for easy installation
• Reusable 3″ air filter with inverted cone design
• 4 Ply silicon connectors with stainless steel clamps
• Air box with rubberized trim
• Bracketry to prevent rattling under engine torquing
• Gains ranging from 9-15WHP on stock vehicle, even more if tuned!
• No CEL, no fuel trim issues

Fitment:

• MK5 VW GTI incl. Edition 35 (2006-2008)
• MK5 VW GLI (2006-2008)
• MK5 VW EOS (2006-2008)
• MK6 VW Golf R (2012-2013)
• MK2 SEAT Leon (2006-2009)
• MK2 SEAT Cupra R (2006-2012)
• B6 VW Passat (2006-2010)
• 8P Audi S3 (2006-2013)

At CTS Turbo we are proud to announce our new 3″ air intake system for the 1.8TSI and 2.0T Gen1 and Gen3 VW/Audi range of vehicles. This kit includes parts that make it compatible with both generations of TSI engines!

The air scoop works in conjunction with our sealed airbox to seamlessly force cold air into our 3″ air intake system.  Air then flows through our high flow cone air filter, which utilizes an inverted cone design for maximum engine breathing.  Our 3″ CNC mandrel-bent aluminum intake pipe allows for smooth entry of cold air into the engine providing peak power gains ranging from 9-15WHP. By using a factory MAF housing (when equipped), you can be sure that fuel trims will remain perfect.

All of the components included in the CTS air intake system work flawlessly together to provide increased horsepower and torque throughout the entire power band and an aggressive race-inspired sound.

This intake kit is designed to be compatible with our TSI Gen1 BOSS kits; intake pipe features 2x 1/8NPT bungs for easy installation of BOSS kits.

Product Details:

• Full 3″ Mandrel-bent aluminum piping with black powder coating
• Compatible with CTS BOSS kits, with provisions for easy installation
• Reusable air filter with inverted cone design
• 4 Ply silicon connectors with stainless steel clamps
• Airbox with rubberized trim
• Bracketry to prevent rattling under engine torquing
• Gains ranging from 9-15WHP on a stock vehicle, even more, if tuned!
• No CEL, no fuel trim issues

GEN1 Fitment (EA888.1)

• MK5 GTI with TSI motor (2009)
• MK5 Jetta with TSI motor (2009-2010)
• MK6 GTI (2010-2013)
• MK6 Jetta GLI (2012-2013)
• EOS with TSI motor (2009-2016)
• Passat CC TSI (2009-2013)
• New Beetle TSI (2010-2013)
• Scirocco TSI (2008-2017)
• Audi A3 TSI (2009-2013)

GEN3 Fitment (EA888.3 non-MQB)

• Volkswagen Beetle (MK2)
• Volkswagen Jetta (MK6) 18TSI & GLI (2013.5-2018)
• Volkswagen Scirocco (MK3)
• Volkswagen Passat 1.8TSI & 2.0TSI (B7)

At CTS Turbo we are proud to announce our new air intake system for the 2.5T EVO MK3 TTRS & 8V.2 RS3 (facelift) 2018 model year.

The OEM air scoop works in conjunction with our airbox to seamlessly force cold air into our air intake system.  Air then flows through our high flow cone air filter, which utilizes an inverted cone design and 4″ Velocity stack for maximum engine breathing.  Our single-piece CNC mandrel-bent aluminum intake pipe allows for smooth entry of cold air into the engine providing peak power gains ranging from 6-11HP.  All of the components included in the CTS air intake system work flawlessly together to provide increased horsepower and torque throughout the entire power band and an aggressive race-inspired sound.

The coupler included is only compatible with the factory turbo inlet pipe. 4″ coupler for CTS Turbo inlet pipe is available separately.

Product Details:

• Mandrel-bent aluminum piping with black powder coating
• Reusable air filter with an inverted cone design
• 4″ composite velocity stack equipped intake
• 4 Ply silicon connectors with stainless steel clamps
• Ram air style airbox with rubberized trim
• Bracketry to prevent rattling under engine torquing
• Gains ranging from 6-11HP on a stock vehicle

Fitment:

• 2018 Audi RS3 2.5T EVO (EA855)
• 2018 Audi TTRS 2.5T EVO (EA855)

At CTS Turbo we are proud to announce our new air intake system for the VW MK7 & MK7.5 Golf/GTI, MK7 & MK7.5 Golf R and facelift Audi A3/S3 is ready! This is the largest intake available, and it is excellent for tuned vehicles that require the extra air flow. 

The OEM air scoop works in conjunction with our sealed airbox to seamlesly force cold air into our air intake system.  Air then flows through our 3.5" high flow air filter, which utilizes an inverted cone design for maximum engine breathing.  Our 3.5" CNC mandrel bent aluminum intake pipe allows for smooth entry of cold air directly into the the engine, minimizing turbulence from unnecessary connections. All of the components included in the CTS air intake system work flawlessly together to provide increased horsepower and torque throughout the entire power band and an aggressive race inspired sound.

Peak power gains range from 10-15HP on an otherwise stock vehicle. We recommend disabling your Soundaktor (noise amplifier) to fully enjoy the true sound of your motor and remove excessive drone caused by the device.

Product Details:

• Mandrel bent large bore 3.5" aluminum piping with black powder coating
• Coveted Laser etched //CTS Turbo logo
• 3.5" Reusable air filter with inverted cone design
• 4 Ply silicon connectors with stainless steel clamps
• Sealed air box
• Bracketry to prevent rattling under engine torquing
• Billet SAI breather adapter and filter (Optional in drop down menu)

• 2014+ VW Golf (all models)
• 2014+ VW GTI 
• 2014+ VW Golf R
• 2018+ Audi A3 (all models)
• 2018+ Audi S3

 NOTE: If you have a Golf, GTI or A3 you will require the SAI breather adapter and filter. Only for vehicles WITHOUT a MAF sensor.

CONFIRM ON YOUR CAR BEFORE ORDERING!

At CTS Turbo we are proud to announce our new air intake system for the Audi 3.0T and 3.2L FSI engines.  The OEM air scoop works in conjunction with our sealed airbox to seamlesly force cold air into our air intake system.  Air then flows through our high flow cone air filter, which utilizes an inverted cone design for maximum engine breathing.  Our single piece CNC mandrel bent aluminum intake pipe allows for smooth entry of cold air into the the engine providing peak power gains ranging from 5-8HP.  All of the components included in the CTS air intake system work flawlessly together to provide increased horsepower and torque throughout the entire power band and an aggressive race inspired sound.
 

Only for B8 and B8.5 Audi S4/S5/Q5/SQ5 with 3.0T or 3.2L V6 engine!

Product Details:
- Mandrel bent aluminum piping with black powder coating
- Reusable air filter with inverted cone design
- 4 Ply silicon connector with stainless steel clamps
- Sealed air box with rubberized trim
- Bracketry to prevent rattling under engine torquing
- Billet SAI breather adapter and Billet bracket with SAI breather filter
- Gains ranging from 5-8HP

Installation guide can be downloaded here

CTS Turbo is proud to release our B8 3.0T Supercharger Pulley Upgrade Kit.  

CTS pulley is smaller diameter than stock. It will increase the speed at which the supercharger spins and will increase the boost pressure output.  Increased boost pressure in conjunction with upgraded ECU software results in a dramatic increase in horsepower and torque throughout the entire powerband. This will not increase stress or excessive wear on supercharger or engine components. 

NOTE: CTS B8 3.0T Supercharger Pulley Upgrade Kit must be used with appropriate "Stage 2" performance software.  
Stage 2+ performance software (not included) will allow you to achieve maximum boost and power from your 3.0T while safely optimizing air fuel ratios, timing, and boost pressure bleed off.  

Most Stage 2+ software tunes are compatible with this kit.

Product Details

• Made in house at CTS Turbo, in Canada
• Precision CNC machined from billet ASI303 stainless steel - best on the market! No other pulley manufacturer uses this steel.
• OEM-spec honing and tolerances
• Replacement supercharger drive belt
• Boost increased from stock 11psi to 15psi, boost holds steady all the way up to redline
• Nitride coated for long-lasting OEM looking finish

Product Details:

• 2.25” Mandrel bent tube
• CNC machined FMIC mating flange
• Black powder coated finish
• Laser cut mounting bracket
• Designed for fitment on cars with CTS TSI K04 upgrade or other K04 upgrade kits (APR, AWE Tuning, etc)

PLEASE NOTE: This product does not include the silicone as per the image. It is expected that you use the silicone that came included with your K04 Upgrade Kit.