IE Performance Cold Air Intake V2 Carbon Fiber Lid (No Intake)
The all-new Integrated Engineering 2.0T Gen 3 Cold Air Intake System for the VW/Audi MQB platform has been completely reimagined and redesigned from the ground up. Featuring a new 3.5" turbo inlet pipe and heat shield that spans the entire length of the radiator inlet to support massive power gains from even large turbo and hybrid setups. New modular design allows the intake to be ran as a cost-friendly open filter intake, or upgraded with a high-gloss carbon fiber assembly further reducing hot engine bay air and adding a high-quality style to your engine bay.
Included:
High-Gloss Carbon Fiber Intake Lid
PACKAGE CONTENTS:
High-gloss Carbon Fiber Lid ONLY (THIS LISTING DOES NOT INCLUDE THE INTAKE)
Get The Complete Carbon Fiber Intake Kit (See below):
This product page is only for the carbon fiber lid. This does not include an intake. We've bundled the intake and cover for your convinience. Combine Performance and style.
With the announcement of our all-new modular MQB intake comes the end of our previous open filter and carbon fiber models. The new intake is higher performing, improved fit, and more budget-friendly for the carbon variation.
IE cone filters are specifically designed for high-flow and perfect fitment to the integrated velocity stack found on most IE cold air intake kits. This is a dry filter that can be oiled, however, we do not recommend air filter oiling on turbocharged or forced induction vehicles. The filter can be cleaned and re-used many times. If you find it difficult to clean your filter or find it severy stained, it may be time to replace the filter element. This is a direct replacement filter ready to keep your car on the road and performing at its best. Includes new filter clamp.
The IE Audi B9 A4 & A5 2.0T Cold Air Intake is the perfect addition to any engine bay. Give your Audi added horsepower, torque, snappier throttle response, and an aggressive sound. Typical peak gains from our CAI are roughly 10-20 Horsepower and Torque.
POWER GAINS
The ram air design, velocity stack, and massive 55-inchfilter inlet help deliver the most HP possible from a cold intake system.
Expect peak gains of 10-20+HP/TQ on tuned engines.
INCLUDED IN THE B9 IE CAI KIT
IE Intake velocity stack & heatshield assembly
IE Silicone turbo inlet pipe assembly
IE 5” inlet performance air filter
IE Turbo heat shield
All necessary hardware (clamps, nuts, bolts, etc)
INCREASED AIR FLOW
This Intake delivers an impressive flow increase to feed your turbo. More cold air flow means more power; especially during the hot summer months. Ditch your stock restrictive airbox for the IE intake System.
DESIGN DETAILS
IE engineers set out to produce the highest performing cold air intake that looks great and fits like a factory installed part in your A4. The latest in computer design and 3D scanning technology were employed during the development process for a perfect fit and maximum performance. The final product resulted in the greatest performing and best-looking intake available.
HIGH-FLOW VELOCITY STACK
Delivering cold air to your engine is a must for making power. The velocity stack efficiently channels air as quickly as possible into the intake system. The velocity also functions as a solid mount for the air filter which means no intake pipes rattling on heat shields.
CUSTOM HEAT SHIELD
IE uses a three piece heat shield which performs and looks great. It effectively channels cold air from the front of the car to the massive performance filter. Furthermore, it eliminates the induction of hot air found in other locations of the engine bay. A second heat shield is mounted above the turbocharger to further protect against power robbing heat off the exhaust and turbo.
PERFECT FITMENT
This Intake fits B9 Audi A4 and A5 without any modification or installation hassles. The install process is simple and can be done quickly with basic tools. The fact that IE intake utilizes the factory airbox mounts ensures a perfect and hassle free fit. Additionally, the stock rubber mounts allow for engine movement which keeps intake components from getting damaged.
CLASSY AND CLEAN APPEARANCE
Wrinkle black powder coated velocity stack and heat shields result in a sleek and sporty appearance in any engine bay. As a final touch, all IE heat shields are finished with a classy, laser etched, stainless steel IE logo badge.
The following power result data was collected on our in-house Dynapack hub dyno. Dyno chart is as tested at 4500 feet altitude with SAE corrected numbers. Before and after results are direct back-to-back comparisons on a full bolt-on stage 2 B9 A4 2.0T engine. The only change made to the vehicle between testing is the swap from a stock intake with a new clean air filter to the IE Cold Air Intake Kit. Dyno power results are approximate and may vary from car to car.
HORSEPOWER & TORQUE DYNO CHART
HORSEPOWER & TORQUE POWER GAINS OVER STOCK
VEHICLE FITMENT
Audi - A4 2015+ (B9) 2.0T
Audi - A5 2015+ (B9) 2.0T
Audi - A4 Allroad 2015+ (B9) 2.0T
This intake does not fit cars that have a MAF housing/sensor.
The Integrated Engineering MK5/MK6 FDS intercooler system was built from the ground up to offer the ultimate in performance for your vehicle. When increasing the power output of your engine it is extremely important to ensure it has the proper cooling to match. It packs a very large intercooler core into the space available, a full 54% larger than the OEM core. This large core delivers cool air to the engine under all circumstances, increasing power and torque and simultaneously reducing heat soak.
When you begin modifying your VW MK7/Audi MK3 Golf R, GTI, A3, or S3 it will become necessary to upgrade the intercooler. Once upgrades such as ECU tuning, exhaust systems, and turbo upgrades are introduced, intake air temperatures begin to rise, resulting in massive power loss.
This charge pipe upgrade Kit for 2.0T and 1.8T MK7/8V TSI engines includes two quality silicone intercooler inlet/outlet hoses and four high-strength band clamps for a direct installation. These hoses are a direct replacement for both IE FDS V2 Intercoolers and the stock factory equipped intercooler. Your new charge pipes feature a flow maximized design with no restrictions for optimized airflow.
Manufactured from multi-ply reinforced silicone for long-life and reliability against expansion or stretching under extreme boost pressures from upgraded turbos and tunes. The ends are molded with a inner flat edge that creates a stop for a perfect and easy no-fuss install and increased reliability against hoses popping off or leaking.
This listing is for the IE POWERlink Flash Tool only. You may also purchase this cable with IE performance tunes for your vehicle (sold separately).
POWER IN THE PALM OF YOUR HAND
Add serious power and fun to your car without popping the hood! The IE POWERlink V4 Flash Cable is the key to uploading IE engine-specific tuning upgrades to your ECU, Simply plug into your vehicles OBD2 port and launch the app on your Apple or Android phone (or Windows laptop). Enjoy serious horespower, torque gains, increased acceleraton, faster 0-60 times, optimized drivability, improved responsiveness, multiple octanes, enthusiast drive mapping and more in only minutes!
LEADING FEATURES
Uploads IE Performance Tunes (sold separately)
Apple & Android mobile flashing app (supported platforms)
Flashes engine & transmission tunes
Direct OBD2 vehicle flashing in only minutes
Customizable live gauge display (Mobile)
Octane and feature switching (varies by platform)
Upgrade tune stages for matching hardware
Return to 100% stock programming at anytime
Read and Clear diagnostic codes
Check and clear emissions monitors
Data-logging (Windows 10+ laptop)
FLASH WITH A LAPTOP
Would rather use a laptop? No problem! IE Flash Wizard Software allows the IE POWERlink Tool to communicate with your vehicle’s ECU to flash software tunes, upgrade, update, data log, or read/write codes on any Windows 10+ powered laptop or tablet.
DEVICE
PORTS
OS
PROC.
POWER
RAM
Laptop or Tablet
Wifi & USB
Windows 10 or newer
32 or 64 bit
1.0ghz or greater
4GB or greater
NOTE: Mobile flashing app requires an IE V4 POWERlink flashing cable and is not compatible with older V3 serial number units. Have a V3 and ready to go Mobile? Simply purchase a new V4 POWERlink to gain full mobile functionality.