SHIFT FASTER, DRIVE FASTER The IE DSG Tune for your Audi B8/B8.5 S4/S5 3.0T delivers increased power, higher RPM limit, faster shifts, optimized shift points, adjustable launch control and additional transmission performance features when paired with a matching ECU tune. Acceleration times will greatly improve turning your tuned 3.0T into a fully rounded performance monster. LEADING FEATURES Lightning fast gear shifts Higher shift points of 7200 RPM Multiple launch RPMs: 3400, 3600, 3800, 4000 Drive shift mapping entirely reworked with an enthusiast in mind Flashed directly through OBD-II Port (No TCU removal required) Works flawlessly with all IE ECU Tunes Unlimited launches (factory defaults to 200) Increased clutch pressure on tap for higher torque without slip Temperature protection remains for safety Gear hunting reduced Gearbox “Torque Limiters” removed WHAT DOES A DSG TRANSMISSION TUNE DO? IE’s Audi S4 (DL501 S-Tronic) DSG tune is all-inclusive and does not offer expensive upgrades. That’s right, there are no unnecessary upgrade charges and all features and upgrades are included at one low cost. A great deal of sportiness is added to the tune while maintaining factory smoothness and driveability that you love about the S4. More aggressive launches and faster shifts are guaranteed to put a smile on your face. Also, expect acceleration and 0-60 times to improve dramatically from a larger useable powerband provided by the higher shift points. REQUIRED FOR SELECT ECU TUNES Required for S4 & S5 Stage 2 dual pulley files, your new transmission tune will no longer lug the engine in drive mode or short shift the larger powerband. Clutch clamping forces are increased so the transmission can safely handle and deliver the increased power and torque. DSG tune requires a matching ECU Tune, do not install on stock ECU tunes. ONE TUNE FOR ALL STAGES IE’s DSG tunes are all-inclusive without any expensive upgrades. That’s right, there are no unnecessary upgrade charges and all features are included from the outset for any level of hardware or ECU Tune Stage, one cost and you are covered for all and any future upgrades from Stage 1 to Stage 2 billion. USER ADJUSTABLE LAUNCH CONTROL The purchase of an IE DSG file grants you access to customization of launch points. With several launch points to choose from you can pick what works best for your setup! Available Launch Control RPMs: 3400 RPM 3600 RPM 3800 RPM 4000 RPM *Some early model B8 DSG TCUs cannot have launch control added to them, as well as some replacement Mechatronics units. Non compatible TCU codes include, but may not be limited to 8K1927156AC and 8K1927156AD. You can use your IE Powerlink tool to check your TCU code. Other DSG tune features will function normally. IE DSG TUNE TECHNICAL FEATURES HIGHER SHIFT POINTS Utilize the whole powerband of your supercharged 3.0T engine without the DSG interfering and shifting early. DRIVE MAPPING REWORKED The B8 and B8.5 S4 is designed to a fault to keep engine rpm extremely low in drive. We completely reworked this, creating a more enthusiast-friendly drive mapping which shifts a bit higher. This eliminates vibration and that constant feeling that you’re lugging the engine. We’ve reworked the downshifting aspect as well, making the transmission much quicker to deliver power when you need it. Thousands of miles of testing were accumulated and a variety of users were polled to come up with this improved drive mode. INCREASED CLUTCH PRESSURE Increasing the clutch pressure allows for the transmission to hold more torque without causing clutch damage or expedited wear. With the increased torque, the acceleration will be greatly increased and launches will far more aggressive. FLASHED THROUGH OBD-II PORT There’s no need to remove the TCU from the car and it can be flashed in your driveway or through an IE software dealer. Additionally, having an IE PowerLink cables means you can install updates are they become available as well as read TCU and ECU fault codes. TAKE-OFF LAG REDUCED The clutch engagement has been reworked to reduce that annoying “DSG Lag” when moving away from a stop. MULTIPLE LAUNCH RPMS The purchase of an IE DSG file grants you access to customization of launch points. With several launch points to choose from you can pick what works best for your setup! FLAWLESS OPERATION WITH IE ECU TUNES The IE DSG Tune and ECU Tunes were developed side by side on our in-house dynamometer. By running both tunes you will unlock the full potential of your 3.0T engine and transmission. Perfect for all IE Tunes from Stage 1 to dual pulley and throttle upgrades. VEHICLE FITMENT Audi - S4 2008-2016 (B8 & B8.5) 3.0T supercharged engines* Audi - S5 Coupe 2013-2016 (B8.5) 3.0T* Audi - S5 Cabriolet 2009-2016 (B8-B8.5) 3.0T* *IE DSG tunes are available only for vehicles equipped with Audi's 7-speed S-Tronic transmissions. Does not function with manual 6-speed transmission cars.

SHIFT FASTER, DRIVE FASTER

Don't short shift your ECU tune and performance parts, get the most out of your modifications with the IE DSG Transmission tune for 2015+ Golf R, GTI, A3, & S3 2.0T. Instantly gain increased power, higher RPM limit, faster shifts, optimized shift points, adjustable launch control, and a true performance tuned transmission. Acceleration times will greatly improve transforming your 2.0T into a fully rounded performance monster.

SHIFT FASTER, DRIVE FASTER The IE DSG Tune for your VW MK6 GTI, Jetta, GLI, or Audi 8J TTS 2.0T delivers increased power, higher RPM limit, faster shifts, optimized shift points, adjustable launch control, and additional transmission performance features when paired with a matching ECU tune. Acceleration times will greatly improve turning your tuned 2.0T TSI into a fully rounded performance monster. LEADING FEATURES Lightning fast gear shifts Higher shift points of 6800 RPM Kick down in manual mode eliminated Lag time reduced when starting off in first gear Multiple launch RPMs: 3200, 3400, 3600, 3800, 4000 Drive shift mapping entirely reworked with an enthusiast in mind Flashed directly through OBD-II Port (No TCU removal required) Works flawlessly with an IE ECU tune Increased clutch pressure on tap for higher torque without slip Temperature protection remains for safety Gear hunting reduced Gearbox “Torque Limiters” removed WHAT DOES A DSG TRANSMISSION TUNE DO? The IE DSG Tune for the MK6 2.0T TSI has been carefully set up to make the car way more fun to drive. It completely reworks the shift point mapping in both drive and sport. The transmission will no longer lug the engine in drive mode. Clutch clamping forces are increased so the transmission can safely handle much more power. Shifts are much, much faster taking time directly off the 0-60 and ¼ mile times. ONE TUNE FOR ALL STAGES IE’s TCU/DSG tune is all-inclusive and does not offer expensive upgrades. That’s right, there are no unnecessary upgrade charges and all features are included from the outset. A great deal of sportiness is added from the tune while maintaining factory smoothness and driveability. More aggressive launches and faster shifts are guaranteed to put a smile on your face. Also, expect acceleration and 0-60 times to improve from faster shifting. DSG tune requires a matching ECU Tune, do not install on stock ECU tunes. USER ADJUSTABLE LAUNCH CONTROL The purchase of an IE DSG file grants you access to customization of launch points. With several launch points to choose from you can pick what works best for your setup! Available Launch Control RPMs: 3200 RPM 3400 RPM 3600 RPM 3800 RPM 4000 RPM IE DSG TUNE TECHNICAL FEATURES HIGHER SHIFT POINTS Utilize the whole powerband of your 2.0 TSI engine without the DSG interfering and shifting early. DRIVE MAPPING REWORKED The MK6 2.0 TSI DSG is designed to a fault to keep engine rpm extremely low in drive. We completely reworked this, creating a more enthusiast-friendly drive mapping which shifts a bit higher. This eliminates vibration and that constant feeling that you’re lugging the engine. We’ve reworked the downshifting aspect as well, making the transmission much quicker to deliver power when you need it. Thousands of miles of testing were accumulated and a variety of users were polled to come up with this improved drive mode. INCREASED CLUTCH PRESSURE Increasing the clutch pressure allows for the transmission to hold more torque without causing clutch damage or expedited wear. With the increased torque, the acceleration will be greatly increased and launches will far more aggressive. FLASHED THROUGH OBD-II PORT There’s no need to remove the TCU from the car and it can be flashed in your driveway or through an IE software dealer. Additionally, having an IE PowerLink cables means you can install updates are they become available as well as read TCU and ECU fault codes. TAKE-OFF LAG REDUCED The clutch engagement has been reworked to reduce that annoying “DSG Lag” when moving away from a stop. MULTIPLE LAUNCH RPMS The purchase of an IE DSG file grants you access to customization of launch points. With several launch points to choose from you can pick what works best for your setup! KICK DOWN REMOVED IN TIPTRONIC/MANUAL MODE The kick down switch is disabled in manual shift mode, ensuring you stay in the gear you’ve selected, even during hard launches or over bumpy terrain FLAWLESS OPERATION WITH IE ECU TUNES The IE DSG Tune and ECU Tune were developed side by side on our in-house dynamometer. By running both tunes you will unlock the full potential of your 2.0 TSI engine and transmission. VEHICLE FITMENT VW - MK6 GTI 2010-2014 (MK6) 2.0T EA888 Gen1/2 TSI engines VW - MK6 Jetta 2011-2013.5 (MK6) 2.0T EA888 Gen1/2 TSI engines* VW - MK6 GLI 2011-2013.5 (MK6) 2.0T EA888 Gen 1/2 TSI engines* AUDI - TTS 2008-2015 (8J) 2.0T TFSI EA113 engines *This DSG calibration is for 2.0T TSI EA888 Gen 1 & 2 engines only. Many Jetta and GLI models are equipped with a new engine variation (EA888 Gen 3) after 2013.5 and later. This tune does NOT support Gen 3 model engine TCUs. Please verify if your engine is an EA888 Gen 1/2 2.0T TSI or EA888 Gen 3 2.0T TSI tune before ordering. IE DSG tunes are available only for vehicles equipped with 6 speed DSG (DQ250) transmissions. Does not function with manual 6-speed transmission cars.

IE cone filters are specifically designed for high-flow and perfect fitment to the integrated velocity stack found on most IE cold air intake kits. This is a dry filter that can be oiled, however, we do not recommend air filter oiling on turbocharged or forced induction vehicles. The filter can be cleaned and re-used many times. If you find it difficult to clean your filter or find it severy stained, it may be time to replace the filter element. This is a direct replacement filter ready to keep your car on the road and performing at its best. Includes new filter clamp.

INCREASE POWER AND SOUND WITH A COLD AIR INTAKE

The IE Audi B9 A4 & A5 2.0T Cold Air Intake is the perfect addition to any engine bay. Give your Audi added horsepower, torque, snappier throttle response, and an aggressive sound. Typical peak gains from our CAI are roughly 10-20 Horsepower and Torque.

POWER GAINS

The ram air design, velocity stack, and massive 55-inchfilter inlet help deliver the most HP possible from a cold intake system.

Expect peak gains of 10-20+HP/TQ on tuned engines.

INCLUDED IN THE B9 IE CAI KIT

• IE Intake velocity stack & heatshield assembly
• IE Silicone turbo inlet pipe assembly
• IE 5” inlet performance air filter
• IE Turbo heat shield
• All necessary hardware (clamps, nuts, bolts, etc)

INCREASED AIR FLOW

This Intake delivers an impressive flow increase to feed your turbo. More cold air flow means more power; especially during the hot summer months. Ditch your stock restrictive airbox for the IE intake System.

DESIGN DETAILS

IE engineers set out to produce the highest performing cold air intake that looks great and fits like a factory installed part in your A4. The latest in computer design and 3D scanning technology were employed during the development process for a perfect fit and maximum performance. The final product resulted in the greatest performing and best-looking intake available.

HIGH-FLOW VELOCITY STACK

Delivering cold air to your engine is a must for making power. The velocity stack efficiently channels air as quickly as possible into the intake system. The velocity also functions as a solid mount for the air filter which means no intake pipes rattling on heat shields.

CUSTOM HEAT SHIELD

IE uses a three piece heat shield which performs and looks great. It effectively channels cold air from the front of the car to the massive performance filter. Furthermore, it eliminates the induction of hot air found in other locations of the engine bay. A second heat shield is mounted above the turbocharger to further protect against power robbing heat off the exhaust and turbo.

PERFECT FITMENT

This Intake fits B9 Audi A4 and A5 without any modification or installation hassles. The install process is simple and can be done quickly with basic tools. The fact that IE intake utilizes the factory airbox mounts ensures a perfect and hassle free fit. Additionally, the stock rubber mounts allow for engine movement which keeps intake components from getting damaged.

CLASSY AND CLEAN APPEARANCE

Wrinkle black powder coated velocity stack and heat shields result in a sleek and sporty appearance in any engine bay. As a final touch, all IE heat shields are finished with a classy, laser etched, stainless steel IE logo badge.

EASY INSTALLATION

Installation is a quick and easy install with basic tools. The process should take around an hour for most enthusiasts. CLICK HERE to view and download the IE B9 Cold Air Intake Install Guide.

INSTALL OVERVIEW VIDEO

DYNO POWER RESULTS

The following power result data was collected on our in-house Dynapack hub dyno. Dyno chart is as tested at 4500 feet altitude with SAE corrected numbers. Before and after results are direct back-to-back comparisons on a full bolt-on stage 2 B9 A4 2.0T engine. The only change made to the vehicle between testing is the swap from a stock intake with a new clean air filter to the IE Cold Air Intake Kit. Dyno power results are approximate and may vary from car to car.

HORSEPOWER & TORQUE DYNO CHART

HORSEPOWER & TORQUE POWER GAINS OVER STOCK

VEHICLE FITMENT

• Audi - A4 2015+ (B9) 2.0T
• Audi - A5 2015+ (B9) 2.0T
• Audi - A4 Allroad 2015+ (B9) 2.0T

This intake does not fit cars that have a MAF housing/sensor.

AUDI B9 2.0T TUNE FEATURES

HOW TO TUNE YOUR B9 A4 or A5

IE ECU Stages for your Audi B9 engine are available for stock (Stage 1) or with modified hardware for Stage 2. Read below to determine the best stage for your build!

In order to flash your vehicle, you will need an IE POWERlink Direct-port Flash Tool (sold separately) and a Windows 7+ powered laptop. Already own an IE POWERlink cable? Contact us to purchase upgrade credits, there is no fee to upgrade tunes and you only pay the difference in tune cost.

Follow the link provided with your IE POWERlink Flash Tool to download our Flash Wizard software and follow the on-screen directions to tune your Audi in a matter of minutes!

WHAT DOES THE IE AUDI B9 ECU TUNE DO?

Your ECU (Engine Control Module) is a computer loaded with maps to control the operating conditions of your Audi 2.0T engine. The factory calibration is designed to function with stock installed hardware, meet new car regulated standards, and de-powered to not compete with higher performance models. IE's motorsport recalibration brings your engine to life by unleashing its full performance potential on stock hardware or to match your installed hardware upgrades while maintaining reliability and factory-like comfort. This is how your turbocharged Audi should have felt from the factory!

 

VEHICLE FITMENT

• Audi - B9 A4 Quattro 2016+ with 2.0T engine*
• Audi - B9 A5 Quattro 2016+ with 2.0T engine*
• Audi - B9 A4 Quattro Allroad 2017+ with 2.0T engine*

*For all wheel drive (Quattro) vehicles only, does not support front wheel drive engines at this time.

When you begin modifying your VW MK7/Audi MK3 Golf R, GTI, A3, or S3 it will become necessary to upgrade the intercooler. Once upgrades such as ECU tuning, exhaust systems, and turbo upgrades are introduced, intake air temperatures begin to rise, resulting in massive power loss.

 • 76mm (3 inch) tubing replaces restrictive 60mm factory tubing

 • Bolt on fitment - no hassle or poorly fitting parts when you choose IE

 • Constructed of 304 stainless long-lasting and high-quality material

 • Thick turbo flange - prevents leaks and warping

 • High flow 200 cell catalytic converter - full power with reduced pollution and smell

 • OEM style flex section - allows for more adjustment and won’t fail

 • All inclusive kit - downpipe, midpipes, all hardware

 • TIG welded construction - equates to long lasting welds that are less likely to fail

Description